cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

2312
Views
0
Helpful
5
Replies

show controllers e1 - question

This command is showing me the following alarms in two E1 interfaces. What troubleshooting should I do? I see alarms in: slip secs, Fr Loss Secs, Line Err Secs, Degraded mins, etc, etc.

Shoul I also check something in the CUCM (ver. 8.6.2.20000-2)?

E1 0/1/0 is up.

  Applique type is Channelized E1 - balanced

  No alarms detected.

  alarm-trigger is not set

  Version info FPGA Rev: 08121917, FPGA Type: PRK4

  Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

  International Bit: 1, National Bits: 11111

  Data in current interval (579 seconds elapsed):

     0 Line Code Violations, 0 Path Code Violations

     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

  Total Data (last 24 hours)

    446 Line Code Violations, 522 Path Code Violations,

     2 Slip Secs, 48 Fr Loss Secs, 2 Line Err Secs, 3 Degraded Mins,

     134 Errored Secs, 26 Bursty Err Secs, 0 Severely Err Secs, 50 Unavail Secs

E1 0/1/1 is up.

  Applique type is Channelized E1 - balanced

  No alarms detected.

  alarm-trigger is not set

  Version info FPGA Rev: 08121917, FPGA Type: PRK4

  Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

  International Bit: 1, National Bits: 11111

  Data in current interval (579 seconds elapsed):

     0 Line Code Violations, 0 Path Code Violations

    200 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

     200 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

  Total Data (last 24 hours)

     0 Line Code Violations, 0 Path Code Violations,

     29774 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

     29774 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Thanks for any help.

Best,

Patricio

2 ACCEPTED SOLUTIONS

Accepted Solutions
Erick Bergquist
Frequent Contributor

Those errors are layer 1 errors with the E1 circuit if they are still incrementing. Clear the counters, show controller a few times and if the errors are increasing then check the cable between router interface and smartjack.

Call your provider and have them
Test the circuit for issues.



Sent from Cisco Technical Support iPhone App

View solution in original post

Hi Patricio,

This errors appear generally when you have a cable problem, try to replace the E1 cable....

Regards

Please rate all useful posts
Favor calificar todos las respuestas útiles.
_____________________________
LinkedIn Profile: do.linkedin.com/in/leosalcie
MDGDP, CCNA, CCNA Voice certified

__________________________________________________
Please remember to rate useful posts clicking on the stars below.
LinkedIn Profile: do.linkedin.com/in/leosalcie

View solution in original post

5 REPLIES 5
Erick Bergquist
Frequent Contributor

Those errors are layer 1 errors with the E1 circuit if they are still incrementing. Clear the counters, show controller a few times and if the errors are increasing then check the cable between router interface and smartjack.

Call your provider and have them
Test the circuit for issues.



Sent from Cisco Technical Support iPhone App

View solution in original post

Ok, thank you for your response.

If there's any other suggestions, they are very welcomed.

Patricio

Hi Patricio,

This errors appear generally when you have a cable problem, try to replace the E1 cable....

Regards

Please rate all useful posts
Favor calificar todos las respuestas útiles.
_____________________________
LinkedIn Profile: do.linkedin.com/in/leosalcie
MDGDP, CCNA, CCNA Voice certified

__________________________________________________
Please remember to rate useful posts clicking on the stars below.
LinkedIn Profile: do.linkedin.com/in/leosalcie

View solution in original post

Thank you Leo.

Replacing the cable will absolutely resolve the problem?

After 515 minutes, it's showing this info now:

E1 0/1/0 is up.

  Applique type is Channelized E1 - balanced

  No alarms detected.

  alarm-trigger is not set

  Version info FPGA Rev: 08121917, FPGA Type: PRK4

  Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

  International Bit: 1, National Bits: 11111

  Data in current interval (99 seconds elapsed):

     0 Line Code Violations, 0 Path Code Violations

     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

  Total Data (last 5 15 minute intervals):

     0 Line Code Violations, 0 Path Code Violations,

     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

E1 0/1/1 is up.

  Applique type is Channelized E1 - balanced

  Description: ## TRAMA CLARO 5551-0600 ##

  No alarms detected.

  alarm-trigger is not set

  Version info FPGA Rev: 08121917, FPGA Type: PRK4

  Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

  International Bit: 1, National Bits: 11111

  Data in current interval (99 seconds elapsed):

     0 Line Code Violations, 0 Path Code Violations

     35 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

     35 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

  Total Data (last 5 15 minute intervals):

     0 Line Code Violations, 0 Path Code Violations,

     1550 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

     1550 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Patricio

And now:

E1 0/1/0 is up.

  Applique type is Channelized E1 - balanced

  No alarms detected.

  alarm-trigger is not set

  Version info FPGA Rev: 08121917, FPGA Type: PRK4

  Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

  International Bit: 1, National Bits: 11111

  Data in current interval (374 seconds elapsed):

     0 Line Code Violations, 0 Path Code Violations

     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

  Total Data (last 6 15 minute intervals):

     211 Line Code Violations, 268 Path Code Violations,

     1 Slip Secs, 23 Fr Loss Secs, 2 Line Err Secs, 1 Degraded Mins,

     102 Errored Secs, 16 Bursty Err Secs, 0 Severely Err Secs, 20 Unavail Secs

E1 0/1/1 is up.

  Applique type is Channelized E1 - balanced

  Description: ## TRAMA CLARO 5551-0600 ##

  No alarms detected.

  alarm-trigger is not set

  Version info FPGA Rev: 08121917, FPGA Type: PRK4

  Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

  International Bit: 1, National Bits: 11111

  Data in current interval (374 seconds elapsed):

     0 Line Code Violations, 0 Path Code Violations

     128 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

     128 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

  Total Data (last 6 15 minute intervals):

     0 Line Code Violations, 0 Path Code Violations,

     1861 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

     1861 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Create
Recognize Your Peers
Content for Community-Ad