Network Access Control

Resolved! LANLITE in Dot1x monitor mode?

Does LANLITE switches support monitor mode? We can't seem to write the authentication open command under the interfaces.

ISE 1.3: Use phonenumber as username in Guest self-service registration portal

Is it possible to feed phone number field $ui_phone_number$ as username on ISE Guest Self-service portal?I would like guests to only enter mobile phone number in self-registration portal and then receive a sms with mobile phone number as username and...

AAA Config and console login

I just implemented some AAA config in the switch configuration so all my telnet users are validated by ISE. But now it looks like the config also affected the console login which was not intended.. How should I implement this without affecting the co...

ISE 1.3 - switch 15.2.3 "AAA not ready"

hi all, when migrating switch from 15.0.1 to the new one I can't get 802.1x working cause on the session there is "blocked on: AAA not ready" previously it worked well - what changed in 15.2.3? I'm not using IBNS 2.0 so the config is the same (typica...

ISE SNMP receiver

Hi. I want to hear this forum about how the ISE can receive SNMP message from Swith or Router? I am interested to send LINKUP and LINKDOWN messages to my ISE server so I can monitor my SNMP messages from the ISE GUI or CLI. But I cannot find any docu...

Session abort when editing user in ACS 5.6

Since the upgrade to ACS 5.6 we are not able to edit user settings in the 'Internal User Identity Store' anymore.As soon as we click the 'submit' button in the 'user edit screen' we are immediately kicked out of the application and we land on the ACS...

ISE 1.3 time zone change

HiCisco Identity Services Engine User Guide, Release 1.2, chapter 5, Administering Cisco ISE, page 5.4 deals with changing time zones on an ISE node. First, it describes how to change the time zone via CLI. Then it goes on to tell you that a) doing...

benefits of Cisco ACS 5.7

Hi Everyone,I am currently using Cisco ACS 5.4 with patch 7 only to manage users logging into network devices (i.e. TACACS+ and radius). Cisco just releases 5.7 on May 12th. Any benefits to upgrade from 5.4 patch 7 to ACS 5.7?on the release notes, ...

Resolved! LOCAL webauth with Wireless Lan Controller and ISE

Greetings,We are planning to set up a guest wireless network with sponsored centralized webauth. I didn't realize this won't work with our current WLC code (6.0.199.4 ) as 7.2 or later is required.We have a project in place to upgrade the WLCs but it...

Limiting ISE Management Access

Greetings,Q1: Is there any way to limit access to the ISE management functionality to a specific physical interface on the appliance?Q2: If the answer to Q1 is no, I see that we can limit access to specific IP ranges. If we do this, does it apply to ...

ISE 1.3 network setup assistant question

I currently have ISE 1.3 with two admin nodes and two psn nodes. We had byod setup until I upgraded to 1.3. I went back through and made sure everything was setup right and even made a few changes, but once I login on a windows 7 laptop I get the e...

Pingable but not HTTPS access (GUI) for ACS 5.2

Hi, Im currently running ACS 5.2 on Vmware with 600GB with 4G RAM , I have problem on access GUI once I have setup my installation in the first stage.Im able to ping its NIC - int g0 I have several things and solution to solve it,- I have renew htt...

Resolved! ISE 1.3 identity purge logging

Hello,we just configured identity purge for our endpoints on our ISE 1.3 Patch 2 deployment. We have a distributed environment with two PAN, two MNT and severl other PSN nodes. Which log-file can verify if the operation was successful and what was do...

AnyConnect Modules - NAM & Psoture

Dear Teambased on clients requirement, we only want to deploy wired & wireless 802.1x and Posture Services for employees. for this we are usingNetwork Access Manager & Posture Modules.We downloaded the iso file and it has all the needed modules, howe...