Hello, We're facing issue with pubd process memory leak, we have to upgrade our switch to a fixed version. The workaround until upgrade is to restart netconf-yang time to time to restart pubd process, it works fine on C9200 serie switches but not on ...
Forum Posts
I am using cisco cbs250-8fp-e-2g. The ap (1852, 2802) is inherited by six generations. The problem is that if 2802 is checked in wlc, the operational status is down and 2.4 / 5G is down. I think it's the poe tribeWhen you do show power inline on the ...
Hello, everyone.I have been recently getting into networking and I have lots of network device to manage. I was considering a switch connected to all management ports of each network device, but also thought of using a terminal server like the 2621 r...
Hello!I can't log in into the embedded AP of an C886VA-W-E-K9. I tried the passwords I remember, but maybe I forgot them.I tried to runrouter#service-module wlan-ap 0 reset default-config and then to log in, both cisco/cisco and cisco/Cisco do not wo...
Hello All,i am facing issue with cisco any connect clientRandomly, i have the error message : "You may need to use a browser to gain" There is no 'wifi portal ' of something like this . i have a direct connexion to internet and i can ping and acces w...
I have acquired a pair of HWIC-D-9ESW cards for my Cisco 2901. Their stacking-ports are connected and switchport stacking-partner interface FastEthernet run on ONE of the ports. As these are Layer 2 interfaces I assigned the entire range of ports to ...
Hello Community,I recently got a Cisco 2960-XR for cheap and it worked fine. I created the User here. After that I updated it since there was an really old Version on it which didnt have and Features. Since then it doesnt really display the things o...
HiI'm trying to copy a fragment of the IOS config (class-map update) into running-config using EEM (2.3 on 12.4.15T7):event manager environment ip1 10.224.129.109event manager applet MACUpdate event timer watchdog time 30 maxrun 5 action 1.0 info ty...
Resolved! Cisco WS-C3850-48F-S Infomation Needed
Hello,I am new to this site and only signed up as I need some info.I purchased a used Cisco WS-C3850-48F-S Switch that I have been told has been factory Reset.The switch is going to be used for POE devices and for personal Server connections.I know t...
Hi, I'm going through this tutorial to learn ansible with Cisco 9k3https://developer.cisco.com/learning/modules/intro-ansible-iosxe/ansible-ios-modules/gather-information/All has been good till the moment I tried to run this playbook (ansible-playboo...
Having same issue with multiple platforms C9300, C2960, C3650.Using copy sftp: flash: the username is not sending to the SFTP server.Yes, SFTP server is configured with username and password. ACH-Playground-SW1#copy sftp: flash:Address or name of rem...
HiI am configuring the netflow on my Nexus:Hardware cisco Nexus9000 C93180YC-FX Chassis Intel(R) Xeon(R) CPU D-1528 @ 1.90GHz with 24569704 kB of memory.I am using these commands:flow exporter PRTG-Exporter destination 10.2.58.106 use-vrf KIS-AD...
Hi there,i'm new to Cisco. We're configuring some Catalyst 1300-Switches and i'm trying to figure out, how i can limit ports to 1 device (MAC-Address). I'm using C1300-48T-4X with the actual firmware 4.1.6.54 in this case.I've already successful setu...
Hi allJust a swift question. I was give the task to split one of the production Networks into smaller parts using VLan's.I learned that there's "The golden rule": one subnet per VLAN.My question is: WHY ?If I'd proceed that way, we'll have to re-desi...
Hello, I am having trouble with this type of router, where I have a set up of 4 wireless routers 8 end devices ( 4 laptops, 4 pcs) and 4 switches. The problem that I am having is that DHCP is configure on 4 wireless routers and all of them has ip add...
