Hi, I am provided with console access to ASA 5510 (v9.0). However, I am not close to the device and hence I am accessing it via Teamviewer. It is a Windows 10 Laptop that is consoled to the firewall. I am trying to identify on how to upload the...
Sir,I have the below case:PC -> Switch -> ASA5510E0/0 is Public with security level 0E0/1 is Inside with security level 10E0/0 IP is 10.10.120.2 (switch VlAN gateway is 10.10.120.1)E0/1 IP is 10.10.130.2 (switch VLAN gateway is 10.10.130.1)PC IP is 1...
What is exact difference between FPRxxxx-ASA-K9 with FPRxxxx-NGFW-K9, and for launching IPS what license do I need?
We would like to know weather Cisco Firepower IPS & Broadcom ATP CAS uses Oracle Java SDK or JRE or not? If yes, Does ArcSight bundle the Java license together? (does it come bundle with the product or require any additional license) As far as I unde...
Hello everybody! A had a problem - Cisco FTD 4145 cluster experienced a failure on one chassis, which caused the application to reboot on its own. Chassis log message2024 Dec 14 07:42:02 FP-Primary %FPRM-2-ERROR: Power-cycle blade 1 due to blade not ...
Hello, I'm more from the Microsoft Azure side of the fence. I understand that Cisco ASA only supports Policy-Based VPN tunnels so Azure has to use the less functional gateway to have a Site-to-Site VPN to an on-prem ASA. This causes huge compatibil...
Hi all,I've configured a Cisco FTD 1010 and I'm having a weird behavior happening. I've configured all the policies from inside to outside and the default action is to block.I've configured several policies and I can see them being allowed and matchi...
Hi guys, Would like to ask how to configure the static route through CLI on firepower 1120? I connected into FTD and tried to add static route but it shown only for MGMT interface, how to configure it on outside interface? (Through the DR test, we ca...
Hi All, Suggest me a firewall with 8 x 10G copper port + 12 x 10G SFP+ port + 4 x 25G/40G QSFP28 port from day one. All ports must be fully equipped with OEM SFP transceiver modules. Cordially Nazirul Bashir.
Good day. We are looking at testing out deploying Cisco ASAv and/or FTD in Azure as part of new requirement. Question I have is it possible to set up high availability (Active/Standby) between two different regions (ie. Active is in one region and st...
I have seen an issue with an ASA setting up a connection and keeping this connection through a wrong interface. Background: ASA is perimeter Firewall, has a default route towards outside and some routes pointing to inside (10.10.0.0) and some to a t...
I am trying to figure out how to add a static ARP entry to the ARP table on my Cisco Firepower 1120. I'll admit I'm very new to this product line. I have two sites and I'm trying to create a VPN between them. My ISP allocated two addresses in the ...
Hello Cisco experts, I bought a used ASA 5510 two months ago for my lab gear, it was working super fine, but two days ago i turned on my ASA to work with and i found my self on the ROMMON, i know that it's tooo weird but even me i can't understand h...
Hello Everyone,We have recently deployed FTDv on AWS and trying to add it to on-prem FMC. Both are on same latest version. I am trying to add command on FTDv to add FMC, from AWS console but its not taking somehow.Can someone plese guide urgently to ...
Hi I am aware that BFD Echo does not work through transparent firewall because of identical source/destination IP/MAC addresses. However, would you be so kind to confirm if Plain BFD is supported (i.e. non Echo mode) If so, has anyone implemented it?...
