Dears, Does any one knows how to configure distribute list with flex config to filter eigrp routes in Firepower 4110. Regards,Graniti
Forum Posts
Hi everyone, I have setup my ASA5506 as illustrated above. GigabitEthernet1/1 and GigabitEthernet1/2 are set to get IP assigned by 2 seperate ISPs through DHCP.I have my workstations connected through a switch to the GigabitEthernet1/4 of the ASA an...
Resolved! firepower 9300 security module issue
hi all, we have an issue with firepower 9300 security module 2.when we are seeing the hardware status it is showing unassociated. we referred the Cisco document it showing " Unassociated—Thesecuritymodule/engine doesn't have a logical-device associat...
Hi everyone, I need to set up a site-to-site VPN between Main and Branch Office.These sites have a Lan-to-Lan, so the new vpn will be a backup. I already created the cli code, but how to set it as secondary? Is there a way to configure metric? Thanks...
I have followed the guide on the link below to configure direct authentication on ASA. HTTP part of it works fine but HTTPS doesn't. http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/113363-asa-cut-through...
Resolved! Changing interface names on ASA
Hi Guys, I have an ASA 5516 with 2 WAN links, one is named outside and the second name backup. Backup line used to be just 4G dongle to keep us online if main line dies, but it was upgraded to a nice, 300/300 mbit connection. The main line is actual...
Hi, dear: I have met an issue when I enable ipv6 feature on ASA 5512. I created prefix 2001:100:101::/64 for interface gi0/0.169. caowen-asa5512(config)# show run int gi0/0.169 ! interface GigabitEthernet0/0.169 vlan 169 nameif inter_vlan169 ...
I've just tried to run up an instance of FTDv in a lab environment for testing prior to using on a customer site, the setup script allows me to manually configure a management address as usual, but this doesn't seem to be being applied correctly. I...
Hi All, I am replacing the existing firewall with Firepower series FPR 4110 model. I am getting issue in making interface up, Also after going through the config guide i have below questions 1. Is all the features are license based, including maki...
I have an ASA5512(Cisco Adaptive Security Appliance Software Version 9.8(2) ). I have Anyconnect setup on it and have licenses for up to 250 users. When I monitor the connections I see that the users are connecting with an SSL-Tunnel but they are o...
how can i fix the error taxii-service received code unbale to run to taxi cisco site how can i find the error and fix it
Hello, I have a situation where I need to configure port forwarding for traffic originating from a specific IP address on the Internet and is then destined for a specific IP address located within our inside network (RFC 1918) on UDP4500. We only h...
Hi all, It is my first time here. So, if I am doing something wrong, please let me know. I am implementing a monitoring tool in a customer - called OPMANAGER.I already exported flow and syslog. But the most important thing to do is: Monitore all the ...
Hi guys , Im trying to configure a port channel beetween ASA (active/stanby) <--> SW 3850.ASA Config interface GigabitEthernet0/1channel-group 10 mode activeno nameifno security-levelno ip address!interface GigabitEthernet0/2channel-group 10 mode act...
Resolved! How to debug to SSH session on ASA
Since upgrading from Pix to ASA, I haven't had to try to debug anything. Today I needed to debug an issue with a LAN to LAN tunnel coming up. I issued the commands I am used to using and so much debug information, not pertaining to what I am wanting ...
