Hello All, We are planning to deploy 3 pair of Firepower NGFWv firewalls in Azure cloud, so I understand they can be managed only by FMC in On-Premise or in AWS cloud. My thought was can't these firewalls be managed locally & individually? I mean l...
Forum Posts
Hi,I like to manage the FirePOWER Services using the ASDM but after I enable the FirwPOWER Services, then I reloaded the ASDM client. Once I reloaded the ASDM client, the Configuration Tab in the ASDM went grayed out but I can see the FirePOWER tab. ...
How much is protect license and why control license can not be verified? i discover IPS can not be applied without protect license and application level can not be used too
We have an ASA 5515 running 9.9(1) providing VPN connectivity only. Remote users are first authenticated via an external RSA service, then a secondary check to our own Microsoft DC's is performed to assign the correct Group-Policy through the use o...
Hi everyone, Hope you can help. I have been on this issue for 3 weeks with two diff Cisco tech support but have no progress. We just got this Firepower 5508-x with base license only back in a month ago. In short, right now, from the lan 192.168.0...
Resolved! How to use SourceFire Product License?
Hi, I have a SourceFire Product License like this. I don't know how to use it with the 5506W-X: Please help. Thank you! Product Name : ASA5506W-CTRL-LICProduct Description : Cisco ASA5506W-X Control LicenseProduct Qty ...
Hello Everyone, Does Cisco support NIC Teaming for Management interfaces on IPS Sensor 8350. Regards, Karthik
We're looking at replacing our older ASA 5505, and trying to decide what direction to go. We 100% need SSL VPN, so unfortunately the Meraki line is out as far as I can tell. So now looking at the ASAs (and which software image we'd run) vs the NGFW...
Hi. We have enabled FDM on our FTD sensor. On our effort to configure anyconnect, we cannot seem to be able to change the Anyconnect listening port from 443 to something else? Is this possible? Also i do not see any flexconfig on FDM, is there a way ...
I'm looking to set up a Firepower 2110 Threat Defense using the Firepower Device Manager GUI. I have a single outside interface set to the main ISP that all traffic is currently routing through, but also have a secondary outside interface for a seco...
I am trying to update Firepower FTD and I have downloaded the following: Cisco_FTD_Upgrade-6.2.2-81.sh and Cisco_FTD_Upgrade-6.2.3-83.sh but when I click to install, I get an error message stating "The requested update is not valid for this model."...
Resolved! Update 5506-X with FirePOWER failover
Hello, I need to update an ASAs failover 5506-X with FirePOWER to overcome vulnerability CVE-2018-0296. I would like to know how I can transfer the .bin that is on disk0: from the first ASA to the second. Regards,
Hello folks, I have a hard time getting my head around Firepower deployment on ASA5506-X, managed with ASDM. I'm trying to follow the manuals but just don't get it. Could anybody tell me the configuration needed (CLI) to match traffic that should...
I have a FMC 1500 that I am trying to update to 6.2.3.7 The automatic updates seemed to have stopped, and when I try to manually download in system-->updates I get the error: "download updates failed: Peer certificate cannot be authenticated with...
Hi I have enabled a log on ACL as below ip access-list extend CAPTURE_BATCH_1_VLAN_103 permit tcp host 172.16.101.108 any gt 0 log permit tcp host 172.16.101.109 any gt 0 log permit ip any any when i do "show log" in the switch, I can see the ACL ...
