Hello, I'm new to the community and hoping someone can shed some light on my issue. I have a leased line coming in to connect two sites, Right now I have an ASA 5508-X that I'm preparing to use for one site. The sites are set up as follows:...
Forum Posts
Dear All, I have a doubt on working with timeouts and state table. Below is the Same output ASA# show conn protocol tcp101 in use, 5589 most usedTCP outside 10.23.232.59:5223 inside 192.168.1.3:52419, idle 0:00:11, bytes 0, flags saATCP outside...
Hi All, What would be the easiest way to refine/analyze traffic in a ACL "permit IP x x". We want to know what kind of traffic actually is within this ACL. The ACL gets about 1000 hits a day. I've already setup NetFlow but i'm seeing more data th...
Hi, I am currently setting up Firepower FTD in VMWare Workstation, and was hoping someone could possibly help me with an issue I am experiencing with the FTD not intercepting and blocking/allowing traffic? A bit background: I now have a paired ...
Resolved! Latest FMC and ASA FirePOWER
hi, i plan to build a lab for projects/POC. i have a spare ASA 5506-X and upgraded the ASA code to 9.8. can i upgrade a "fresh" ASA FirePOWER module directly to 6.2.3 (from 5.4.1)? is there a TAC "recommended" FP image? asasfr-5500x-boot-6.2.3-4.img...
Good day, I would like your help regarding my simple topology. Here it is below: I was trying out my failover by shutting down interfaces and seeing if an automatic failover occurs. All is working but one. When I shut down the Gi0/24 of the L3...
Resolved! ASA 9.1(7)31 not booting
Hello community, I upgraded an ASA 5540 from 9.1(7)23 to latest 9.1(7)31. Sadly at the first boot of .31 interim, the asa not booting up and hung. After changing boot image back to .23 at ROMMON, the ASA booting up fine. Did someone have this iss...
i install new Cisco_Firepower_Management_Center after reboot webpage not working please help me urgent i user this command but problem did not fix please help urgent root@FMC:~# pmtool restartbyid httpsd i reinstall fresh new Cisco_Firepower_Man...
Resolved! FTD as IPS Deployment
Hi Guys, I am deploying a new 4100 as an IPS but when I register it in FMC it shows routed mode. Does it affect the IPS if it run in routed mode? I just want my IPS like a bump in a wire so I decided to configure it with inline pairs. Does it still c...
Hi Guys, I am configuring a standalone FP4110 to run FTD application. I configured platform settings of the FXOS chassis however, I got a validation error when I am trying to configure the Syslog section. Below is the error message, "Same hostname ca...
Hello everyone , We have a deployment where we have 2 Cisco ASA 5516 with FTD Image installed as HA Pair on Firepower Management Center and we need to replace them due to an RMA . We wander what are the steps to accomplished the replacement with...
Hello Everyone , We are running FMC/FTD (4110) v6.2 , is it possible to create a PBR policy with IP SLA for Active/Active dual ISP scenario ? So far i am able to configure PBR with next hop but dont see any option to tie in IP sla with route map ?
I want to see the sessions table from a PIX with Software Version 8.0(4). following one session seen using the "show conn" command (the IP addresses have been changed for security reasons): 134 in use, 3212 most usedTCP outside s10.102.128.89:8080 ...
Resolved! Basic NetFlow questions for ASA
It's the first time i'm actually configuring NetFlow. I've read the instructions how to configure NetFlow but i'm having 2 questions.1. I just want to export traffic from one interface, but we already have a TCP-Bypass Policy Map on that interface. C...
Resolved! Configure "http redirect 80" in FMC
Hi All, I am struggling with this. I want anyconnect users who accidentally go to http instead of https to be automatically redirected to https. I believe the command "http redirect outside 80" will do this but I can't figure out where to do this...
