Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hello, I can not open Rommon mode in my asa 5505.    CISCO SYSTEMSEmbedded BIOS Version 1.0(12)13 08/28/08 15:50:37.45 Low Memory: 632 KBHigh Memory: 507 MBPCI Device Table.Bus Dev Func VendID DevID Class Irq00 01 00 1022 2080 Host Bridge00 01 02 102...

lezgin000 by Level 1
  • 590 Views
  • 0 replies
  • 0 Helpful votes

Hi,I had a unit of Cisco ASA5505 firewall unable to complete the boot up and display error message as below:i2c_read_byte_w_wait() error, slot = 0x4, device = 0xa0, address = 0 byte count= 1. Reason: I2C_HOST_BUSY_ERRORFailed to read offset 0 from ID...

Trying to figure out the best placement for a Cisco ASA 5508-X in our network that already has a Cisco 2900 router in place for the edge WAN and some internal Cisco Catalyst core and distro switches.   In a dilemma whether we should place the ASA in ...

Hi   Come up with this probem while trying to set up remote backup. Ive tried a few times and finally got nfs to work to my server, but it was the wrong directory it was pointing at.  Now when trying to add another directory it comes up with the erro...

silkeborg by Level 1
  • 7413 Views
  • 6 replies
  • 0 Helpful votes

Resolved! ASA 5506-x image

Hello,   I just received a new ASA 5506-x with Firepower Threat Defense (ASA5506-FTD-K9) and noticed that this has a consolidated image of the ASA and Firepower services. The ASDM has apparently been removed. I have been reading that this consolidate...

Hi,    I haven't had much luck on responses to this however here goes. I have an IPSEC VPN tunnel up and connected. I can ping a remote IP address from a local address however I cannot Telnet to Port 55019 of the same remote IP Address. It seems that...

Hi,   We are in the process of carrying out the following:   A. Move our VLAN Layer 3 Virtual Gateways from our core switch to our Internal ASA Firewall. We will create sub-interfaces on the "Inside" interface for each VLAN and use that sub-interface...

peni.nscg by Level 1
  • 1614 Views
  • 3 replies
  • 0 Helpful votes

Is it possible to bind multiple interfaces on the 5506-x into one logical interface? The office I am installing the 5506 has 3 PC's and one server. I will be putting the server in a DMZ area and I would like to use three physical interfaces on the AS...

So this is a totally new thing for me but we have a client who has given us a list of about 1000 HTTP user agents they want blocked and they do not want to do this on the actual web server.    I found an old example of how to block an agent on an ASA...

Hello,   I am hoping someone can shed some light on how to connect an ASA/Firewall to a vPC pair. The design is to connect an ASA via a port-channel to a vPC  pair (NK7Ks) The ASA has L3 interfaces and I am trying to find out if configuring a L3 port...

zekebashi by Level 4
  • 4199 Views
  • 4 replies
  • 0 Helpful votes

Hi, We are having ASA 5555X single appliance with FTD running 6.2, Now we have to introduce HA standby appliance into the network. What is the step by step approach to achieve this. Is there any downtime required for this? Please help.   Thanks.

Review Cisco Networking for a $25 gift card