I need to reset my username and password
I need to reset my username and password
Hi Experts, I need to get some insight on this issue as when I try to configure an interface with a IP address and save it..! IT DOES NOT SAVE? What seems to be the problem. This problem started from the time a reset the device to factory default an...
Dears, i have a concern regarding deploying and designing firepower next generation IPS appliances 8250 in multi-tenancy deployment, as i need to have inline IPS appliance running in two different zones (edge and DC), at the same time to have higher ...
Hi Team, Good day! I have encountered problem to do reimaging/restore for Sourcefire Sensor 3D2100.Issues descriptions: Unable to proceed with reimaging/restore of the sensor from software version 4.10 to 5.2, the screen as attached.Current software ...
Hi All, Yesterday, i faced the problem with ASA5585 firewall. I configured and reboot firewall then it come down to default configuration again. How can i fix this error? Please help me.
Hi Guys, I got a question about ASDM real-time log viewer. I tried to simplified my question to easy understand version below. ACL access-list FROM-CORE permit tcp any host 10.1.1.1 eq 53 access-list FROM-CORE permit ip any any log I've enabled th...
Not sure if this is the right place to ask. Is it possible to add a static route of a network set in a Cisco ASA? In our setup there are a number of networks and hosts of the RFC1918 network that we will need to route to a different interface then th...
I have 2 cisco ASA 5512 units (security plus license) in an Active / Standby HA Failover cluster (I've tested both stateful and stateless failover unsuccessfully). Both units are connected (over a switching path) to a VRRP - enabled gateway, set up b...
Hello, Can someone point me in the right direction on this issue. Basically I have an ASA 5506 and I want to allow access to a web server on the inside. Wan IP 172.16.5.1 Inside Server IP 72.16.4.10 Ports Below I cant seem to get the Nat working r...
Hello, I have a question what is the best pratice for static NAT and access-list. Example: web server(192.168.1.1) inside to outside(10.10.10.10) with port 80 and 443. ip nat inside source static tcp 192.168.1.1 80 10.10.10.10 80 ip nat inside source...
Hi all,does someone know if is possible to binding the management of SourceFire sw Module on an ASA5515X to a different interface than management0/0 ?Thank you.Mauro
Hello Guys, I have one question regarding connect to mysql in sourcefire 5506.I researched many sites, but i didn't get any result.Anyone can guides, how to connect to mysql sourcefire 5506 from mysql navicat?Best Regards,Chhayheng
Noob here. I am having problem configuring ASA to statically nat a server on dmz directly to an outside interface on port 80. I was able to successfully nat it using another IP address (12.12.12.5) but not if I used outside ip (12.12.12.2). Here's a...
Hi Just for the curiosity, how we can create an extended access-list with Object Group with my example: show object-group object-group network SSL network-object 10.30.40.0 255.255.255.0 network-object 10.30.58.31 255.255.255.255 My-FW(config)# a...
Hi guys, I've setup a lab with 2 x 5505 ASAs and 2 laptops trying to improve my understanding of ASAs and securityI've attached a diagram... I'm trying to get Laptop A (192.168.10.2 /24) ping/access IIS on laptop B (192.168.20.2 /24) Unfortunately I ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-21-2024 11:29 AM | ||
06-21-2024 05:54 AM | ||
06-17-2024 12:34 PM | ||
06-12-2024 10:19 AM | ||
06-12-2024 08:28 AM |
User | Count |
---|---|
7 | |
7 | |
5 | |
4 | |
2 |