Hi All, In our current environment S2S vpn is running on 7.2.5 with two interface -outside and inside .Now we want to enable RAVPN in same ftd instance and want use same public ip for RAVPN and S2S vpn. Need your expert opinion -Is there any problem...
Forum Posts
Hello, when i try to edit secure client profile client from asdm, i get this message :ASA version 9.16(4)14ASDM version : 7.19
what is speed of FPR 1120 ethernet port
Hi, I have following situation: 1 x FMC 7.4 3 x FTD 7.4 (each FTD on different remote location) I need Secure Client VPN on each FTD, which is not a problem. VPN should authenticate against FTD's local Active Directory server and with backup to centr...
Hello, I have had my FPR1010 for a while now. To my understanding, there is a 200 GB embedded SSD storage in the appliance. I was just reading about an M.2 slot to expand the storage but have not opened the appliance yet as I am not in position to ...
Resolved! Is AES-256-CBC the same as AES-256-SHA?
Trying to VPN peer an ASA 5505 to a 3rd party's Palo Alto. The only IKE/IPSec options they have are CBC and GCM. Are either of those the same as the AES256-SHA that the ASA's support or am I out of luck?
Recently added a new l2l vpn tunnel for a new site and after building out and bringing up the tunnel, all connection profiles and crypto maps are now missing from the asdm > configuration > site-to-site vpn > connection profiles list and asdm > confi...
Hi, I am trying to recover access to the FDM on a FirePower 1010 NGTW.I have tried to reset the unit to factory with limited success,I am currently trying to reset the management to factory default config, but am getting the following error:> configu...
Hi I have a concern with using Equal Cost Multi-Path for dual WAN to be able to use both WAN connections concurrently, however my concern is how a public website will respond if it sees connections coming from different public IP addresses.If each WA...
I'm trying to configure remote access vpn. I can connect from my web browser and login fine.When I use the AnyConnect client, after entering in the ip address and port number, I get prompted about the certificate warning, I get prompted for my userna...
Resolved! CISCO ASA
Hello Team,I have a cisco asa firewall connected to ISP. I have allowed internet access of downstream devices on the asa.I have a case where, servers downstream are able to browse internet, but not able to ping for example 8.8.8.8.is there an acl res...
Under Management portalAfter adding a few bits (Ports, Networks + Group and Policy) the deployment failed. I tried to add ports 9443 and 6443, but this also led to failed deployment. I am lost on why the failure is happening on small changes too.
Resolved! Upgrade FTD 2140 via cli
Hi All,We've been seeing mysterious reboots of FPR2140 running 7.2.4, so logged a TAC case.According to TAC we were hitting the following defects.https://bst.cloudapps.cisco.com/bugsearch/bug/CSCwh10681 [bst.cloudapps.cisco.com]https://bst.cloudapps....
I would like to install the new cisco secure client 5.1.4-74, which will auto update when remote users log in. However I would only like to install the vpn client, and not the rest of the msi's that are loaded in the cisco-secure-client-win-5.1.4.74-...
I am not sure if this is possible, but I can't get it to work.We recently setup an IPSEC/VTI VPN with 'vendor A'. That tunnel and VTI interface are up. Routes are being exchanged via BGP. The VPN was setup on a Cisco ASA. The ASA has 2 VPN's to 'vend...
