Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

I have an 881W that I am trying to setup a zoned based firewall. Here is what an excerpt of it looks like: ----------------------------------------------------------------Current Config:----------------------------------------------------------------...

Hello,Been reading the following info - http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/113396-asa-packet-flow-00.htmlCan someone advise when the Security-Level of an interface is checked during the pack...

GRANT3779 by Spotlight
  • 2347 Views
  • 1 replies
  • 0 Helpful votes

Hello everybody,I would like to now if i can build cluster failover between differente version ios in my case fw 5510 or 5540 with 8.4 and fw 5555 with v9.1.5 ??.I have also workaround is to install ios v9 1.5 version on fw 5510 or 5540 in order to h...

Yasm by Level 1
  • 544 Views
  • 2 replies
  • 0 Helpful votes

Hi,I am trying to connect vpn client (Win XP) and its works just fine. It is also communicating with radius server and internal network no issues in that. However, when using vpn client on Win 7 it does not connect. I can see from the debug in firewa...

Hi,My Cisco ASA 5505 will now not boot to any versions of the OS v8.x. (8.0.2 through to 8.2.2)It will boot to v7.24 with no problem.It has 256MB RAM and 128MB flash.When attempting to boot to v8.x it just sticks on "Loading..." and won't proceed.Doe...

 Dear All, I have deployed Cisco ASA 5525 IPS for one of our customer in inline mode in internet block. I am redirecting traffic from ASA towards built-in IPS module using ACL ( permit ip any any), class map and global service policy. I have verified...

rmujeeb81 by Level 1
  • 902 Views
  • 3 replies
  • 0 Helpful votes

hi all,i'm trying to create a trust point and an identity certificate at the same time but the ASA can't seem to allow me.i tried to do it both in CLI and ASDM but no avail. anything i'm missing here? ASA5505(config)# crypto ca authenticate TP-5505ER...

Hello Everyone, I have a need to multihome out two MAN links to the same ISP. The two links will connect via an ISR and will participate in an eBGP adjacency. On the internal side, iBGP will be used to create the alternate default route to the ISP. E...

mbram1313 by Level 1
  • 1472 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Monitor SNMP Trap

i have configured the port securities on my switches..its working fine...but i want to monitor the SNMP trap ie the port violation count ....is there any tool or something which says me that on that switch someone has violated the port security

  Hi.. I have cisco ASA version 8.4,i am settingup a L2L IPSec tunnel with our client. Client too has ASA. I have disable AM mode on my end ASA.Does AM need to be disable on client end ASA to  get the negotiation happen b/w ASAs and tunnel up and wor...

Anukalp S by Level 1
  • 335 Views
  • 2 replies
  • 0 Helpful votes

Looking thru the ASA spec sheets I really don't see a "real world" performance metric.  For instance, Cisco claims 500Mbps multiprotocol stateful inspection througput for the 5512-X.  So let's say my Internet connection is 20Mb.  Does the amount of u...

tato386 by Level 6
  • 634 Views
  • 3 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card