Resolved! How to allow protocol 97 in PIX 515E
What would be the access-list entry to allow protocol 97? I am setting up foreign-anchor controller and need to allow protocol 97.Thanks.
What would be the access-list entry to allow protocol 97? I am setting up foreign-anchor controller and need to allow protocol 97.Thanks.
inside: security level 100outside: security level 0traffic coming in from any IP address on inside interface & going out on outside interface with destination of 12.1.1.1 should be NAT'ed/PAT'ed to 100.1.1.1 IP address. How do we do it in ASA running...
I have an application I have to support where there will be two custom HTTP headers inserted into the normal HTTP 1.1 message. Let's call them "X-Header1" and "X-Header2."I want to be able to allow only HTTP traffic that has these two headers (and t...
HiI recently found a use for an old PIX 506 that I found in our store cupboard.After doing a 'show ver' I noticed that although the number of internal hosts was unrestricted, the throughout is 'limited'. The outside ethernet is registering as 10/half...
On8.3/8.4 I can setup a translation to translate an internal host to another outside IP addres, only for connecting to one outside host, and the rest of the translations to outside are done dynamic using the outside IP. Can this be done on 8.0 code?
Hi All,I few employees within our network require access to an external network using a Nortel VPN client. I am fairly new to firewalls and have configured a simple zone based firewall using Cisco CCP firewall wizard, basic - low security. The Nortel...
Hi,I need to have a IDS/IPS for my local users in my network. we have 3xcisco 6509 in access layer switch with 4 VLANS and I am looking for a system to detect activities like Port scan, IP scan and ,... in local network from the workstations.Please a...
Hello allTrying to setup a DMZ on a ASA5505 with UL and Sec+ licenses.inside 10.20.0.0 DC/DNS 10.20.2.1 Fileserver 10.20.2.3DMZ 10.21.0.0 App1 10.21.2.1 - Outside 12.12.12.3 App2 10.21.2.2 - Outside 12.12.12.4outside 12.12.12.2My en...
We have one pair Cisco ASA 5505 located in different location and there are two point to point links between those two locations, one for primary link (static route w/ low metric) and the other for backup (static route w/ high metric). The tracked op...
Hi Everyone,If i need to open specfic port on ASA so that it allow the traffic for that.What are different ways to open port using CLI?ThanksMahesh
Hi Everyone,I read that ASA do statefull inspection and it inspects all the contents of the packet .Need to know which command we can use on ASA to know it is doing statefull inspection.also is there any command that can disable the statefull featu...
I have a DGway of 31.210.99.10/27 and i want to translate the ip addr to 192.168.xx.xx ( internal ip SNMP) to 31.210.99.xx/27i did the commands static (inside,outside) 31.210.99.xx 192.168.xx.xx metmask 255.255.255.255access-list 101 permit tcp any...
Dear CiscoI have two 5505 ASA. I would like to know can I make two 5505 failover reduntant with active standby setup?RegardsAlan.
bonjour,nous avons un souci depuis ce jour avec nos 2 ASA 5520. Sans raison, le principal bascule tout seule, sans raison vers le secondaire au bout de 3 minutes. Le principal est OK, aucune erreur, si on le remet principal tout va bien mais au bout ...
I have an SSL (client) VPN set up on my ASA 5520. It worked with a self-signed certificate and one locally generated username/password. Taking the next step, I'm trying to get the firewall to connect to my Domain Controller via LDAP and authenticate ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 08-26-2026 04:36 AM | ||
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM | ||
| 08-20-2026 05:54 AM | ||
| 08-19-2026 07:59 AM |
| User | Count |
|---|---|
| 3 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |