May be a simple question for someone, but I need to see if anyone can give me the syntax for a port forward.I need to forward port 55443 to an internal address ( lets call it 15.15.15.15) from two outside ip's ( 5.5.5.5 and 6.6.6.6)These addresses ne...
Hello,I have one public IP address but multiple local servers that run on the same port. I cannot change the port the clients use to connect to this server, so I can't do a port map in my NAT router. The solution I had in mind, is to filter on source...
HI Experts,In my lab setup i configured Cisco 3560 switch.VLAN 20 and VLAN 30 i configured.VLAN 20 interface IP : 192.168.20.1/24VLAN 30 interface IP : 192.168.30.1/24.Inter-vlan communication is happening fine.For testing for purpose i configured ex...
Hello everyone, I have Cisco ASA 5505 Firewall with security plus license, Currently I open ports on 25,80,443 on public IP address 1.1.1.1 and perform static nat between the inside and outside IP address Such as i configured via CLIaccess-list OUT_...
Hi Guys,I’m trying to configure my ASA 5505, in order to allow my inbound and outbound mail communications. Here with this mail I’ve attached a diagram which illustrates my exact network setup along with ip addresses.In this setup I’ve enabled port f...
Hi,Is there any way or command to type so that it can tell u that this IPS is inline or promiscuous ?in another word how can i check which mode my IPS is running ?thanks
Is there any way to access a MS Exchange Server 2007 on Windows server 2008 through an ASA 5510 running 8.4 with a full MS Outlook client (not using OWA - web browser)? OWA is currently working fine but I was wondering if access via the full Outlook...
HI, I have an ASA and we now have a requirement that we need to be notified in case of a security concern. I have the firewall sending syslog messages to a central syslog server but I would like to know based on what syslog keywords should I be send...
Good Day i try to install CSM 4.0 on WIn server 2008 Ent. R2 (64 bit).but i get the attache error. can anyone help me.
Does anyone know if its possible to set up active/active failover using etherchannel on 5585s? Just getting into the planning stages of a solution.
Hi,I'm new with the ASA.We have a working config with 1 external IP, we need to a second webserver (https) and it should be routed via a second public IP adress.I already tried some suggestions from the community but haven't been able to find the sol...
Hi,Could somebody tell me what do I need to buy to renew the ASA-CSC10-PLUS license for two years?Thanks in advance!
hi guys,i must translate port 80 from outside connection on port 85 in lan serverhow can i configure the asa firewall rules for complete this task?thx to replayLuca
Hi there,Recently I want to apply traffic shape on my ASA5520, but after entering the configure mode of policy-map, I couldnot find the shape command.. If I type the command, the device would notify me that there is no such command.. My version is 8...
Hello,after upgrading an ASA 5520 to 8.4.2-8 VPN clients traffic is not passing destinations other then destinations behind the inside interface. the log shows routing failure for the vpn client on the inside interface.it was working fine with 8.4.1 ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 01-21-2026 03:34 PM | ||
| 01-21-2026 11:24 AM | ||
| 01-20-2026 01:44 PM | ||
| 12-31-2025 01:53 AM | ||
| 12-15-2025 09:32 PM |
| User | Count |
|---|---|
| 4 | |
| 4 | |
| 3 | |
| 2 | |
| 1 |
