How To Block Free Proxy Server if the port is 80 or 8080 ?Thx
How To Block Free Proxy Server if the port is 80 or 8080 ?Thx
I'm having an issue where when I upgrade from 8.2(5) to 8.4(2) on an active/passive asa 5585 running in transparent mode I can no longer reach the standby ip. The BVI interface appears to be created properly, the device IP and standby IP are listed i...
Hi all,i have to include the devices Cisco 2921/K9 e ASA5520-BUN-K9 in a network i'm configuring for a Belarus client.My doubt is:what kind of bundle i have to use for belarus: K9 is right?I can not find any documents to show me what encryption algor...
Hi.I have a problem with failover. On My site I have 2 Firewalls 5580. And I did this configuration on my firewall.interface GigabitEthernet3/0description LAN/STATE Failover Interfacespeed nonegotiatefailoverfailover lan unit secondaryfailover lan in...
I would like to setup a small home network with an ASA firewall and an 871 router for testing purpose so I can get familar with the ASA commands and concepts. Is there sample config I can be pointed to?
Hii have thought many times about outside Nat but i m confused when will be such situation that we will require outside NAT.Can anybody give me best example of real Network, and explain me the traffic flow i have read in book but still it is not clea...
Hi,I have a pair of 5585X-SSP20's which is working in active/standby multicontext mode.The code is 8.2(5) and i have the ASA5585-SSP-20 VPN Premium license.I am planning to utilize the 10G interfaces. Is it possibel to have a single license for 10GE...
I have three interfaces configured, outside, inside and dhcp. The IP for the inside is 10.10.220.101 and dhcp is 10.10.230.1, with same−security−traffic permit intra−interface configured but still not able to communicate between interfaces. The err...
hi,Currently we have two inter-chassis FWSM redundancy. I would like to configure them for intra-chassis.Both FWSM's are in slot 7 of 6509 switches and i want to take secondary out from one of the 6509 switch and insert in the slot 3 of primary switc...
Hi all :I think the ASA5505 I have is in basic license. When I open the third interacse : dmz it must activate No Forward command then can work.Any way to resolve this problem? is it must pay money to buy the license so that can work without No Forwa...
I'd like to monitor the state of Bypass mode for the ASA-SSC-AIP-5 and would like to know if I can check this with SNMP and if so, which OID.I started messing with SNMP and the SSC5 a while back and started a thread about snmpwalk causing it to crash...
Hi all, I have this issue, I save the configuration in the ASA 5505 using write memory or using copy run start but whe i unplug the power cord and plug it back in the ASA gets its factory default configuration.... then what i do is a copy start run ...
Hello,I woulk like to know if ASA 5550 apliance is able to handle SCTP (IP protocol 135) stream in terms of allowing/filtering based on FW rules. We have a problem, though we allowed SCTP IP prot to go through an interface, however I can see that 135...
Does anyone know how to let facetime going through Cisco ZBF ?It uses a bunch of ports like describled in Apple's KB: http://support.apple.com/kb/HT4245 Now what can I do if I let those protocol going out:class-map type inspect match-any INTERNET-ACC...
Hi all :Attach is my ASA5505 config file.I am trying to ping from my inside host (192.168.1.110) to outside host (192.168.2.5) but could not make it. In fact, the inside is with high security (100) and outside low security (0) and this shoud be no pr...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-22-2026 05:00 AM | ||
| 07-16-2026 06:39 AM | ||
| 07-15-2026 08:48 AM | ||
| 07-13-2026 11:05 AM | ||
| 06-24-2026 08:00 AM |
| User | Count |
|---|---|
| 3 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |