Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

My ASA just crashed.Can anyone help me with the crashinfo? I looked over the ASA bugs but there are so many with "Thread Name: Dispatch Unit"Thread Name: Dispatch UnitAbort: Watchdog failure    vector 0x00000000       edi 0x1c6d0794       esi 0x00000...

Hi,I have a newly setup ASA5505 running 8.0, with remote access (anyconnect) workingThe clients can reach LAN, and vice versa.I'm trying to figure out how the h*ck the nat is built, Ive even set all incoming and outgoing traffic to permited but with ...

3moloz123 by Level 4
  • 1682 Views
  • 4 replies
  • 0 Helpful votes

Hi ALLI found a tricky task for our ASA 5505 firewall. I am not able to go internet when using DHCP but I can access by using fixed IP address in client PC.Same IP, Same Mask, Same DNS, Same Gateway. All the same but no hope. What is your opinion? An...

Hi,I have the following config on a 887VA. Will this stop all traffic hitting the outside interface? I want to stop all unsolicted traffic, including icmp echo request, on the outside interface.No ssl, no snmp, no telnet, no ssh, no icmp, no udp, no ...

lcaruso by Level 10
  • 4455 Views
  • 5 replies
  • 0 Helpful votes

Can anyone elaborate on an IDS solution for a virtualized environment? I  have blade servers running ESX/ESXi - heavily virtualized environment.  Im using blade switches as chassis I/O - no pass throughs.The  requirement is to run an IDS service such...

lamav by Level 11
  • 3720 Views
  • 3 replies
  • 0 Helpful votes

Every 7 days (give or take a day) the PIX stop letting traffic through.  I reset the modem or reload the PIX traffic resumes.  Is it possible the modem is updating (maybe updating isn't the correct word) and the PIX isn't updating with it? When i's i...

How do you open a range of ports on the PIX Firewall CLI for the rules and NAT?We have this configured on our PIXstatic (inside,outside) tcp interface 3389 192.168.1.250 3389 netmask 255.255.255.255 0 0access-list 101 permit tcp any host 173.13.28.14...

mdargin by Level 1
  • 1263 Views
  • 1 replies
  • 0 Helpful votes

We have a PIX 535 with unlimited lisence, it has 1,048,953 in use connections because the timeouts have been changed to 24 hour. I am addressing this issue but was wondering why its so high when the max concurrent sessions is supposed to be 500,000 a...

JIM T by Community Member
  • 972 Views
  • 1 replies
  • 0 Helpful votes

Hi all, does anyone know how to send a ENTER (or Carriage Return for you guys who are oldschool) when using the CLI-tool in ASDM 6.4? I need to confirm a previous command with Carriage Return but that doesn't work only by hitting Carrige Return in th...

jkellers by Community Member
  • 1057 Views
  • 1 replies
  • 0 Helpful votes

Sorry, if this is a newbie kind of question, but I've been a networker for quite a while but this issue is a little confusing to me.I have 10 phone switches on 10 different subnets aand each has a unique port number to which I connect, all behind an ...

Review Cisco Networking for a $25 gift card