Hi, anyone impacting with this bug id
Forum Posts
Resolved! %ASA-4-106023
Hi all,I have one constant syslog message in my ASA 5520, everyday i have this message: %ASA-4-106023: Deny Deny icmp src DMZ:X dst INTERNA: YBut the source is a Public Ip X sending to Y a Private ip in my network. my DMZ have access to the internet...
Subject: Accidentally set Password Recovery Functionality to Disabled for Cisco ASA 5506-X Firewall After Following Guide with Conflicting InstructionsGood day from Singapore,On 12 Jan 2024 Friday, my colleague Danial Robinson asked me to go to our c...
I am in the process of migrating FTD 4110 configuration (version 7.0.4) to FTD 3120 (version 7.2.8) that is managed by FMC 2500 (this manages multiple FTD instances). New FMC is 2700 (version 7.4.0). FTD 3120 will be soon managed by FMC 2700 once mig...
I have a scheduled backup Configuration and Operation data Cisco ISE using SFTP server. When the schedule is execute, it created a 0 byte size in server. But if I use local disk repository, backup files were created normal. Is there something wrong? ...
Cisco Secure Firewall Threat Defense Software Snort 3 Denial of Service VulnerabilityIn that vulnerabilityFPR4112 equipment is 7.4.2, and it is guided that the patch is required in 7.4.2.2 versionI would like to ask if it is okay to proceed with the ...
Hi Team, I've configured Route Based IPSec Site-to-Site VPN according to the guide: Configure Route Based Site to Site VPN Tunnel on FTD Managed by FMC - Cisco When I deploy the config, I'm getting the following error: Refer to the following troub...
I have a legacy ACP rule on an FMC managed FTD with an FQDN as the destination. The FQDN no longer exists but the FTD is continually trying to resolve the hostname. I've disabled the rule (not deleted it) but the FTD continues to try and resolve th...
How to disable the rate-limit alltogether - or at lest configure a higher value than 120 api-calls / minute ? According to the cocumentation: The Firepower Management Center REST API implements rate limiting to reduce network load.The API will ac...
Hi,We're having a Firepower 1120 that does AnyConnect VPN peer and FMCv 7.4.2.1. In the Remote Access VPN Dashboard not all active sessions are shown, compared to the output of show vpn-sessiondb anyconnect via SSH on the FTD itself. Seems it shows o...
Resolved! CSICO FTD/FMC IPS
Hi All,I have an issue with IPS on FMC. I have already added the IPS license into the FTD, but when I try to create a new access policy and add an intrusion policy, I receive the following error: “This rule requires an IPS license, but at least one t...
Hello, I'm running firepower 3100 cluster in native mode not multi-instance. must i upgrade the FXOS ? or it will be upgraded same as 2K
We currently use ISE-PIC as our identity source for identity based policies in our FMC. According to the following EOL notice, ISE-PIC support will end November 30, 2027. https://www.cisco.com/c/en/us/products/collateral/security/ise-passive-identit...
hi out thereWe have a couple of FMC 2600 running 2.7.2-500 which i would like to migrate to a virtual FMCv - i expected if i was on 2.7.2 on both "platforms" it would be simple - but no - when i load the backup on a FMCv running 2.7.2-500 it complain...
Hello everyone, I have a design question regarding software compatibility. We are planning to deploy a Cisco Secure Firewall 3110 and our FMC is a hardware appliance model 1000. According to the official administration guide the minimum supported sof...
