Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

We are working with a customer who has a pair of Pix515E firewalls.  Their application sends a lot of email which the windows boxes that were sending the mail could not keep up with the load.  The solution we implemented consisted of 4 Linux hosts to...

mwkirk by Level 1
  • 415 Views
  • 1 replies
  • 0 Helpful votes

In CSM 4.0.1, I have a discovered ASA-5510 device. I've been playing around with deloying policies to the device, and during the last attempt to deploy a policy, I canceled the deployment attempt because the device was not responding.Then I decided t...

jkeeffe by Level 2
  • 1473 Views
  • 2 replies
  • 0 Helpful votes

Hi,I do "show int g0/0" and see a lot of packets dropped on the outside interface of my ASA 5540. The CPU and memory utilization is low. Below are the outputs of "show int g0/0" and "show asp drop".I would like to know the reasons of packets droppe...

pxh by Level 1
  • 3838 Views
  • 3 replies
  • 0 Helpful votes

hi,I have configure ASA 5510 in transparent mode.The management ip 172.168.22.254 .I have my computer connected to the inside port Eth0/1 of the firewall with IP address 172.168.22.2/24I have a router connected to the outside  port Eth 0/0 of the fir...

HelloI wonder if this i popssible on the ASA:got an asa5505 with 4 customers behind it, now we would like to guarantee eatch customer a minimal bandwith of 0.5 mbit and at the same time allow bandwith usage up to 50mbit for these 4 customers.//Rulif

HelloCan someone please clarify on the below configurationWe use eigrp,bgp, multicast,ipx on the network. can someone please clarify the below config specially the access-list allow_all and the action. The access-list do have ip any any. Since we use...

Hi all,I'm about to upgrade the IOS-image on my ASA5550 and also at the same time upgrade the ASDM. I have a few questions about this event.Some info about the ASA5550;It's running IOS-version 7.2(4)ASDM-version 5.2(4)Total Flash is 256 MBTotal Memor...

darkdi0dx by Level 1
  • 6746 Views
  • 6 replies
  • 0 Helpful votes

I have a basic question as to how a firewall works.Say there is a server in the DMZ zone with a private IP of 10.11.1.4  and it is statically NATTed by the firewall to a public IP of 100.11.1.4. Now when a packet with the destination of 100.11.1.4 hi...

mukundh86 by Level 1
  • 447 Views
  • 1 replies
  • 0 Helpful votes

Hello everyone, I would like to know how can i backup configs for our asa5510 incase of failure.  Is it simple to just copy configs from command "#show config"?Also how can enable GUI intrface(asdm) for 5510? is their any security risk enabling GUI? ...

lawsuites by Level 1
  • 8050 Views
  • 4 replies
  • 0 Helpful votes

Hi Experts...........I have a ASA5510, it is currently running 7.0.8. Its RAM and Flash size are 256MB. Could I upgrade from 7.0.8 to 8.x??????Which is the stable version in 8.x trail???? Now my plan is to upgrade to 7.2.5... Please help ASAP....Than...

vipinrajrc by Level 3
  • 3024 Views
  • 12 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card