Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hi,I currently have a Static Nat for example ( web1-internal ) to ( web1-external ) - see Static Nat below !!!Which allows external hosts to connect on a public address and then get translated to the internal address host !!What l want to do now is p...

sgalloway by Level 3
  • 1218 Views
  • 5 replies
  • 0 Helpful votes

I am currently configuring an AIP SSM module on an ASA, and I would like to know which interface IP address should be used for the management interface.  Should it be the outside interface of the ASA or the inside interface of the ASA?

rafrancis by Visitor
  • 2919 Views
  • 11 replies
  • 0 Helpful votes

Troubleshooting the ASA tip:If you're like me, you perform MANY different tasks throughout the day.Many times, I am duplicating the same work at different times throughout the day.It takes a lot of time to figure out and setup a capture session each ...

fsebera by Level 9
  • 1059 Views
  • 2 replies
  • 0 Helpful votes

How good is asa5510 as firewall.  Becasue someone try to convice me that asa5510 is not good firewall becasue when we create owa or remote access connection it's hit the firewall directlly and not good.  Isn't that is with every other friewall.  Just...

lawsuites by Level 3
  • 524 Views
  • 1 replies
  • 0 Helpful votes

I just upgraded my Cisco NAC from 4.6.1 to 4.7.2 so I could manage my 2975GS switches. My last TAC case stated that when 4.7 came out it would support the 2975GS model. However, I do not see the 2975GS as a managed model. Is that correct or is there ...

markbhiga by Community Member
  • 1002 Views
  • 1 replies
  • 0 Helpful votes

We have 2 ASA5520 firewalls setup as Active/Failover running in single router mode.IOS is version 8.0(4)Doing a capture we continue to see one firewall talking to the other (as expected) but the communiction is via IP Protocol 105 (which appears to b...

fsebera by Level 9
  • 14675 Views
  • 2 replies
  • 0 Helpful votes

Hello All,We are migrating our Active Directory 2003 R2 to Active Directory 2008 R2 on domain controllers. Is there any known issue with 2008 R2 and Cisco ASA 5520 or the version which I am running on the  device ?I am running the following version o...

We have two ASA5520 firewalls running 8.0(4).512MB DRAM256MB FlashCPU Pentium 4, Celeron 2000 MHzPurchased 2008 We need to upgrade the memory to 2GB DRAM to support 8.3 but I keep seeing hardware restrictions related to physical memory slots on the m...

fsebera by Level 9
  • 1429 Views
  • 2 replies
  • 0 Helpful votes

HI,i want to know if is correct this configuration for FWSM routeing.i have a router 7200 with a lot of nekwork. Default route to internet a FWSM inside a Catalyst 6509. Catalyst and Rotuer use EIGRP to change routing table.i use on the FWSM this rou...

f.mottini by Level 1
  • 2250 Views
  • 7 replies
  • 0 Helpful votes

First, I want to admit my limited knowedge about the Cisco device and the process I'm going to describe.  I have been working on this issue on and off for weeks with no resolution so any help would be greatly appreciated.After installing the ASA 5510...

buzzstryker by Community Member
  • 5354 Views
  • 10 replies
  • 0 Helpful votes

I am using ASA5505s in my small offices and an ASA5520 at my central sites.  I have configured EZVPN network extension and everything is working perfectly.  I now want to add another layer of security to this configuration.  My understanding is the 5...

Phil Sova by Community Member
  • 1329 Views
  • 3 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card