Hi All,can anyone advice int the below error message as it happened to me twice:Error: Cannot communicate with mainApp (getVersion). Please contact your systemadministrator.Would you like to run cidDump?[no]:I have 4IDSMs (2 on each 6513 core) and th...
I realise thatthis is more inteneded as a support forum, however I have been trying to track down an organisation that can install an ASA5505 in our Chicago office (875 N Michigan) and cannot find anyone who supports small businesses. I'd have a cra...
Hi,I have 2 ASA 550, one is active with its failover with version 7.2(2).I want to upgrade this image to 8.0(3), if this possible, and if so, i must do it for every one alone or on one of them and it will be copied by default to the failover.Here you...
Hi,On CSM Client >device> Access rules is showing the old config and not showing the active running config. Where as tools>preview configuration show me the running config.How do I make the csm client show the running config.Thanks.
Hello,I am having Cisco 2801 Router, just for testing i have applied secure boot-image, now i want to get it back to normal state through consolebut i am unable to do that.when i issue the command show secure bootset, i get the below output.WAN-R...
Hi,Is it possible to access internal servers using public IP. The server and the client, Both are in inside DMZ.The server has a static nat.The client uses global IP. ASA 5540 is been usedRegards,Manish Gupta
I have install the image of Cisco4255 IPS from 6.0 E3 toIPS-4255-K9-sys-1.1-a-6.2-2-E4.img. After this i have got this problem that,The Network Security Level contained in the sensor's displayed in IDM/IME viathe Network Security Health gadget report...
We are setting up security camera system so would like to open Inbound Ports:80 and 443. Also how do you reserve ip address in DHCP scope and create NAT beween private IP address and public IP addres. I am new at this so can you please help me with...
Hi Guys,Need to ask a question on pix. The following ip address is configured on the pix inside interface:ip address 10.150.255.228 255.255.255.248 standby 10.150.255.229The routing is configured asroute inside 10.0.0.0 255.0.0.0.0 10.150.255.227The ...
I am configuring a pair of 5580's to run in transparent mode. From reading a plethora of documents, I understand that multicast doesnt pass native and that you have to use ACL's. I dont deal with multicasting on my side of the house, that is handle...
Hi All,we have ASA 5510. it's conencted to internet and MPLS cloud by outside and inside interface respectively. we'd like to setup EIGRP routing protocol on ASA, if internet link is being down, default route will be changed to MPLS cloud. we added d...
Hello GS,I have two Firewalls ( PIX and ASA ) connected each with a Router which is connected to ISP.I am looking to have Failover over between these two Firewalls so that internet traffic should autodivert when one of the ISP fails.I am struck at t...
Hello Guys, I have a Pix 506E and do not have the password or any configuration information for it. How do go about resetting it to it's Factory Defaults Manually? I really need to...
Hello all, We currently have a 4Mb/s fibre Internet connection, the Output on this interface is consistintley at the limit of the available bandwidth (please see the attached photo from the ASDM). We host our own website internally, so I know th...
Hi all...i've a problem with my asa....i don't know how i can redirect ip to my proxy in my local network before it ip go to internet over the asa ???Please help meee :'(
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 09-11-2025 03:28 PM | ||
| 08-29-2025 08:17 AM | ||
| 07-16-2025 04:21 AM | ||
| 07-06-2025 01:40 PM | ||
| 07-04-2025 01:59 AM |
| User | Count |
|---|---|
| 6 | |
| 4 | |
| 4 | |
| 1 | |
| 1 |
