Dear Team Members,Greeting to all!Currently I'm facing with the port forwarding issues for Port 80, I have two wan interface primary is VPN and secondary is OUTSIDE. I set to VPN interface default route administrative value to 1 and secondary default...
Forum Posts
Resolved! Teardown TCP connection
Hello Team,I'm working as SOC analyst, I'm analyzing CISCO devices and i get one alert regarding Teardown TCP connection from CISCO FTD. <182>May 24 2023 03:53:45 FTDP : %FTD-6-302014: Teardown TCP connection 259297712 for WAN_A:95.214.27.136/43134 t...
Hi Everyone,I am struggling with the ASA configuration with 2 Subinterfaces and am not able to ping from one vlan host to another vlan host, I haven't applied any ACLs and NAT as am not testing it with the internet.int gi0/0.10vlan 10nameif VLAN10sec...
We just upgrade to FMC v7.0.1 and afterwards we seeing an issue with a Health Alert that we cannot clear. The following is showing for one of our FTDs. At the interfaces shown are disabled interfaces on the FTD that are not in use which they should b...
Resolved! NAT Translation in Cisco FMC
Hello all, I'm using cisco FMC 4600 to manage FTD cluster and I need to get NAT statistics and events. As which internal IPs have been translated to a certain NAT IP address. Is there a way to do that in FMC?Thank you, Hadeel
Hi,I'm a starter in configure an enterprise level auth for wired and wireless.I previously config a VPN use cisco FTD and anyconnect as client. the authentication on VPN I can use both certificate and password, I notice that RADIUS server in this cas...
I receive a list of unused rules (hundereds of unused rules) that needs to be deleted from the ASA I can't seem to find any help on this topic, Is this really a mostly manual process? Please is someone able to share a less painful way of executing th...
Resolved! FPR1010 power off
How to poweroff FPR1010 gracefully?
Hello, Do you kwow how to fix the opt/ partition full problem? Storage on local flash drive of fabric interconnect: Partition Size (MBytes) Used Percentage ---------------- ---------------- --------------- mnt_boot 749...
Hi friends,I have a Firewall 5520 with 3 interfaces: Inside (Host: 172.16.10.0/24 and GW: 172.16.10.2) Outside (119.202.193.81) and DMZ (182.16.10.1)I did connect LAN cable on the Server (182.16.10.99) direct to GigabitEthernet0/2 on Firewall ASA 552...
Hi, We see "Encrypted Visibility Engine" (EVE) on the FTD is supposed to replace the SSL Decryption feature. Our requirement is to fully detect and block malware over encrypted traffic (HTTPS). At the present time (May 2023) is safe to use EVE inst...
Dear community,I'm trying to automate Cisco FMC (v6.2) using Ansible tower (v2.9.27), But I have problems with starting the connection,known That I want to use "HTTP API" connection, so may you help me understand the steps to build this connection,Th...
Hello everybody, I upgraded our customer's ASA5555 cluster from 9.14(3)15 ---> 9.14(4)22. The upgrade procedure was without issues.After the upgrade the customer called me and told me that all AnyConnectlogins were impossible.I compared the configura...
Hi to all,I've try to import an ASA configuration to firepower 1140 using the firepower migration tool 4.0.I can upload the ASA configuration correctly, but when try to connect to firepower the migration tool show an error like it:Bllocked Invalid FM...
Hi,I have a Cisco ASA 5520 and connected with a cisco switch. Am working cluster Master/Slave which is working well and looks fine without any issue (UP).Problem is that my Port-Channel is not coming up on switch and ASA both sides the summery of eth...
