I have an Firepower ASA with Firepower base license. Device successfully registered via smart licensing. Now we don't want to connect it to the internet, so disconnected it from internet. Is there any issue if license authorization communication fail...
Forum Posts
Resolved! Can't login to FTD GUI
I am unable to login to the FDM GUI ISA3000 FTD 7.0.1 using the local admin credentials after initial setup on the CLI. I can access the the FDM landing page through the web browser but get a red x above the login prompt after entering the admin cred...
Resolved! Cisco FTD Supported SSH Version
Hi Guys.I hope you are doing fine. Our infrastructure is being audited by an auditor and they asked us to provide a proof which shows FTDs (We are using Cisco Firepower 2100 series) use SSH version 2.I looked everywhere in order to find out about the...
FPR 2110 with ASA 9.14.3.18Hello, everyone,we have an architecture of two ASAs with the above versions that failover between them and are clustered.Last week we noticed that when doing failover communication with the hello message , some vpn clients ...
ASA5525 HA pair: ASDM only accessible to secondary (not primary)...Hello.With ASDM software I am able to access the ASA pair only through the secondary device (ip address). When I try with the primary IP address, I receive error "unable to launch dev...
Hello all, happy Wednesday.We have a Firepower 2140 on 7.0.1.1 build 11, and prior to yesterday, our outside IP range was limited to a single /27 network. Yesterday as part of a HSRP installation, we got assigned an additional outside range, a /28. ...
Hello Everyone,please support to get this issue resolve. I have Firepower 2130 and trying to upgrade the firmware of the device from (6.3.0.4-44) to (6.3.5 or 6.4.0). however when I choose the firmware file and click on install button device complete...
Hello,I am trying to register a FPR1010 FTD (7.0.5) to FMC (7.2.1)- FMC is registered to Smart Licensing- registration over management interface- ping between FTD and FMC is successful- verified registration-key- with or without NAT-IDRegistration ti...
What would be the best way to migrate a current FMCv 7.2.1 which hosts 4 NFGW to another FMCv without losing configuration.Create a backup of the managing Firepower Management Center FMCv and import it to the new device, without losing any configurat...
Resolved! LOCAL Server Group Account Lockout
Scenario: I'm on ASA 5555Users/AAA > AAA Server Groups > LOCAL Server GroupEdit > Enable Local User Lockout > Maximum Attempts = 3I can't find any info about how/where to unlock an account or if it happens automatically.
Resolved! Configuring Control Plane ACL on ASA
Hello,I configure a control plane ACL to a outside interface for limiting AnyConnect access on ASA 5520, will enter the following commands on the device:! interface GigabitEthernet0/0! nameif outside! security-level 0! ip address 1.2.3.4 255.255.2...
We are analyzing the logs from all of our devices. Recently, a question came up on the %FTD-6-302013 message. It appears to be only happening on outbound connections from the inside network to the outside. We never see messages like that for connecti...
I'm running the VM version of the FMC. I have 7.0.4 installed. When I go to an SFR module and go to Advanced Troubleshooting, the only option I have is "File Download". I don't have any tabs for Packet Capture or Packet Tracer. What could be caus...
Does changing these types of parameters in the FMC apply to all devices managed via FMC such as the FTD?
Resolved! FMC Upgrade versions
Hello,I have a Cisco SFR in the form of an FMC running version 6.7.0.3. It is supporting firepowers running version 6.4.0.132. The FMC is just an FMC; it is not an FMCv300. For some reason, I was under the impression version 6.7 was as high a vers...
