Hi ,I have a question about ASA which i happen to come across Is it not possible to NAT with logical IP addresses or IP addresses for which physical interfaces are not configred on the ASA.If not then how can i NAT for multiple IP pools of my ISP for...
I have two DMZsDMZ1192.168.1.1security level 10DMZ2 192.168.2.1security level 5If I want the lower level to be able to communicate with the higher level DMZ:static (DMZ1,DMZ2) 192.168.1.0 192.168.1.0 netmask 255.255.255.0 0 0access-group dmz_allowed ...
Hi ,I am using pix515e.I am unable to ping from Inside server to Outside interface but from pix i am able to ping the outside.interface Ethernet0 nameif Outside security-level 0 ip address x.x.x.x 255.255.255.224!interface Ethernet1 nameif Inside sec...
could anyone please tell me whether cisco supports both of these now
Hi,We have three sites all connected via MPLS running BGP.We are planning to use DMVPN over MPLS for all the above three sites.We want to have hub & spoke topology.We wanted to decide on the routing protocol to be used within the DMVPN tunnel.We want...
Hi all,I'm very new into the IPS configuration.When i enable the auto update form cisco, do i still need to configure the sensor? Are the package files (.pkg) automatically applied to the sensor and capturing/blocking mailicious traffic ?Thanks
We have IPSEC access to the ASA. The users authenticate using username and password. HTTPS has also been enabled on the ASA. We would like to limit remote management access to the ASA. 1)Are the following configurations accurate?hostname(config)#ssh ...
We have an ASA5505 configured for client and clientless VPN access. When using the AnyConnect VPN client, we are unable to resolve machine names without having to fully qualify the domain. For example, instead of specifying exchange we must specify e...
We are using an ASA 5505 in a small office LAN environment. When we try to run the update process on a postage machine (the machine connects to an ftp server to download updates) the process always times out with 0% transfered. I set a capture on the...
Is it possible to password the console port on a ASA5505 so anyone plugging into it doesnt even get the > prompt without supplying a password? Kind of like putting a password on "line con 0" in IOS.I have a bunch of these 5505's I am sending out to t...
Hello All:I did a search for past responses but nothing gave a definate response. I was hoping someone could enlighten me with a push in the right direction to getting the proper config for this scenario.I have a test lab, there is a single ASA 5510 ...
I use a external AD database for vpn authentication login.I just noticed by default, asa only allow 3 simultaneous login per account. I tried to login vpn using multiple PCs with same username, but only can login with 3 PCs, as long as I tried fourth...
hi, Could you please let me know how to do source address NAT'ing on FWSM.Source IP: 1.1.1.1Ingress interface: DMZ1Ingress subnet: 1.1.1.0/24Egress interface: DMZ2Egress subnet: 2.2.2.0/24The Source IP 1.1.1.1 initiated from DMZ1 should be natted to ...
I am not able to configure the following on Cisco ASAdeny tcp any any fragmentsdeny udp any any fragmentsdeny icmp any any fragmentsdeny ip any any fragmentsAre these valid/supported ACL entries on ASA.
I have a local office here that I have deployed a Cisco ASA 5505 device. To enable remote access for employees, I have enabled VPN access using an AAA server that authenticates requests from the Cisco VPN clients on the router. The remote employeees ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 09-22-2026 04:13 PM | ||
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM | ||
| 08-20-2026 05:54 AM | ||
| 08-19-2026 07:59 AM |
| User | Count |
|---|---|
| 4 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |
