I have had the following problem before but I cant remember what I did. Could anyone help.My vlan1 inside interface is set to administratively down. and when I ping its says inside interface is shutdown.I have tried issueing the no shutdown command b...
Hi,Can someone tell me the commands/access-lists on PIX to allow the below:source: 10.10.2.3destination: x.x.x.20ports: 21,23,1530, 18102, 18103Please give me the commands to run on PIX?Regards,Vin
Hi, i need to replace my existing firewall pix 515e with ASA5510 and CSC-SSM .can i save the pix configuration and then load it into the ASA firewall ?
Hello,i use router 1812, IOS 12.4.(6)T5 advanced ip service .is there a limit number pf VPN connections that this router accept for site-to-site ? How can I find this number ?thank u!
Dear AllI can't access internet from my inside network!!I don't know why!?Router :Interface Ethernet f0/0: IP 195.xxx.xxx.17/29 (connect to router) ASA NETWORKInterface External e0/0 :IP 195.xxx.xxx.18/29 (connect to router)Interface internal: e0/1...
Hi,I have a problem with an ASA, I cannot send a ping to a directly connected modem in outside ASA interface.The ACLs is set to permit IP any to any.And the static rules are:access-list inside_nat0_outbound extended permit ip 10.0.0.0 255.255.255.0 a...
Can someone tell me if i can use supernetting for the below subnets rather using multiple entries on PIX?10.91.100.0 / 2510.91.102.0 / 2510.91.104.0 / 2510.91.106.0 / 2510.91.108.0 / 2510.91.110.0 / 2510.91.112.0 / 2510.91.114.0 / 25& it wil be very ...
Hi,Our pix 506e firewall (this is the first time we are setting it up - it is a used device) is connected through ethernet 0 to a router, but we are unable to find the IP address assigned to it to access the configuration utility - Cisco PIX Device M...
Hi all.I need a help in making an internal website available for external users. I have a PIX 502 firewall that has a static public IP.My internal Webserver has a private ip.the website can be accessed internal by : http://server_ip:8080/zak/index.ph...
Hello,I have a PIX 515E and it shows constantly high CPU usage and not sure which process exactly eats that.---------------- sh cpu usaCPU utilization for 5 seconds = 90%; 1 minute: 89%; 5 minutes: 84%--------------- I did show process-------------s...
Hi all,Any one know where I can find a config guide / template for an IOS FW that allows all company data (RFC-1918) down a L2L VPN and has a internet traffic bypass secured by CBAC. I know there is lots of info on each but not together. I'm configur...
Haven't done this in a while and am a little rusty. Need to change the ipsec site to site peer address on a tunnel, a one router is changing locations/ip address.The current cryptomap config is :crypto isakmp policy 11 encr 3des hash md5 authenticat...
Hello;I got the nessus plugins from tenable web site and uploaded it to the nac manager then tried to apply the plugins in the plugins setup but i didnot find anything is there any cli or installation proccess i need to perform to has the nessus plug...
I have a bunch of Cisco ASA unit's all sending tcp based syslog data to a central Kiwi Syslog server. I have the units configured to continue functioning after syslog communications failure.We have patches applied on a regular basis and when the Sys...
I am trying to monitor traffic on an ASA 5510. I was hoping to use SNMP to get this data to a monitoring/graphing tool such as cacti. I already have SNMP giving me the overall traffic picture.I can easily see the data I want to capture by using ASDM ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-16-2025 04:21 AM | ||
| 07-06-2025 01:40 PM | ||
| 07-04-2025 01:59 AM | ||
| 06-19-2025 07:32 AM | ||
| 06-17-2025 01:07 PM |
| User | Count |
|---|---|
| 10 | |
| 5 | |
| 5 | |
| 2 | |
| 1 |
