I have a host in a lower sec that needs access to a router in a higher sec. I have an acl and routing to the inside for the destination network. Do i need to use a static nat for this? I also tryed to create a static nat to the router. But that ...
I have a host in a lower sec that needs access to a router in a higher sec. I have an acl and routing to the inside for the destination network. Do i need to use a static nat for this? I also tryed to create a static nat to the router. But that ...
Hi i have a network running eigrp and my default gateway is the ASA 5510. THe network runs find but i want to set up remote connectivity through the other site incase they loose link with IPSEC tunneling. I have establish Ipsec between sites (ASA a...
what should be the ip address of aip-ssm module? from the inside network range? and what should be the default gateway? I cannot reach it...
Last night I upgraded our ASA 5510 platforms from 7.0 code to 7.2 code.I also shipped the new ASDM image to Flash (5.2.3).this morning I wanted to access the ASDM launcher,so I navigated to https://<address of ASA>. I attemtps to authenticate me to ...
Hello,My customer have a ASA 5550 in HA. It is the Internet Firewall.In this moment the firewall have 50.000 connection. Customer review the log in the syslog server and noted wich not all syslog messages the firewall are notify to the syslog server...
Does the PIX 515 ver. 6.2 support L2TP, IPSEC certificates through itself to a 2k3 server?
A network engineer was in the middle of setting up a customer ASA 5510 Firewall and left. We don't know the IP/UN/PW.Is there a way to hard reset the firewall back to manufacture settings?Thanks in advance.
Hi,I need to terminate the my internet link from ISP on my firewall directly.Old scenrio is something like that.ISP-->Link on ethernet (Cisco router)-->ASA firewall(Natting here)-->SwitchNow want to do something like this.ISP---->Link on ASA firewall...
My VPN go up only if i ping from a specific side.If i ping from the other side the VPN don't go UP and the message is MM_NOSTATEThe good side is pix.txt confThe bad side is pixe.txt conf
Hi,I have a Pix 525 firewall in my lab and i am practicing in it.I have connected two systems to inside and outside interface each.i have configured 172.25.15.1 as inside interface ip address and 172.25.30.1 as outside ip address i want the system w...
Hi,i hav ePIX 515E firewall,from the console,I am not able to enter into if configuration to assign IP address,meanspixfw#conf tpixfw(conf t)#interface e0 here when I press enter it has to go to the ethernet interface prompt but it is not,instead it ...
After I restore the CSA MC 5.2.0.245. I am able to get everything back. I am able to ping the hosts so DNS is working. However the hosts is not register to the MC. Even the MC itself is not register. Is there anything I have to do after the restore?
I want to set up Active/Standby stateful failover. I only have 4 interfaces and 1 mgmt port. I have a outside, inside, and DMZ port configured. I want to use the last port for the stateful information and the MGMT port for the failover information...
Hi,I just took over management for a PIX running 6.3 only using conduits and outbound statements.Currently, there is no Internet (or outbound) access allowed generically speaking for the dmz lan.I have two questions:What are the thoughts of allowing ...
What logging levels would be necessary to identify inside IP addresses in a PAT configuration on a pix firewall?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-16-2025 04:21 AM | ||
07-06-2025 01:40 PM | ||
07-04-2025 01:59 AM | ||
06-19-2025 07:32 AM | ||
06-17-2025 01:07 PM |
User | Count |
---|---|
10 | |
7 | |
5 | |
4 | |
1 |