Does PIX allow PBR, like routers allow?ThanksAlan
Does PIX allow PBR, like routers allow?ThanksAlan
Hi,I voluntarily look after a simple MS Small Business Server 03 network at a charity and made the mistake of buying a Pix 501 to replace a basic firewall we had. I say mistake because if I would have know about the dreadful user manuals and tricky s...
I just had a password recovery for IDS 4215 with 4.1 version. What i performed was to break the boot sequence and went through Recovery process. The password has been reset, IDS is working fine now however everytime the IDS is rebooted, i see IDS pr...
Dear sir,iam having ASA-5520 while configuring iam getting a messiage given belowthe 'vpngroup' command has been deprecated, and will be converted to the corresponding tunnel-group and group-policy syntaxiam not able to connect to vpn PLZ helpme out ...
I want to test my IPS triggering an inbound IPS Sig event. Can anyone advise if Cisco has test attack files available to download for this purpose?Regards
I have an IPSEC between a pix 506 and an ASA5510. The tunnel is over DSL links and there is a problem with traffic not going through correctly. Initially I was trying to get a server remotely to join the domain across the VPN but this was timing out...
Can you NAT an internal IP to the external interface IP? I'm used to doing this on sidewinders but it's giving me an overlap errorThanks
Greetings allI have a question for anyone using any Cisco IDS products.How often the Cisco IDS/IDSM update it's signatures and are the updatescomparable to Snort? Example: An exploit is known...Snort publishes anupdate...can a similar update be found...
I have got two PIXs, Primary and SecondaryPrimary (192.168.1001.1) is StandbySecondary (192.168.1001.2) is ActiveWhen I try to access the PDM from primary (Standby) I could not, but I was able to access PDM for Secondary (Active)Secondary?s PDM Tools...
Any one can help me as how to configure in ASA as i have only one public IP address but i have to configure them for my two servers in my DMZ ... one is FTP and one is WEB server,,,,
When setting up the Stateful failover link, are there any issues if you use the management interface or should you only use an ethernet interface?
I have a pix with one static outside IP address and have been asked to forward a whole bunch of UDP and TCP to an internal (natted) IP address. I have done static mappings before but for only single port numbers. Below is the range of ports to forwar...
I have a PIX-506E set up locally and a PIX-506E set up at a Site 1. I can connect to Site 1 from my backup internet connection which isn't firewalled. When trying to connect to Site 1 through Local PIX I secure the communication tunnel.. but it will ...
Is there a way in the ASA to tell if it was started by a power up or by the reload command ? It doesn't show in the show version.Thanks
Hi, In cisco document http://cisco.com/en/US/customer/tech/tk648/tk362/technologies_tech_note09186a00807ca437.shtml#ios gives a table-2 showing the fixed version of PIX and ASA.Cisco PIX Platforms CSCse60554 Fixed in Version 6.3(6). Cisco Adaptive Se...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
04-17-2024 12:36 PM | ||
04-17-2024 07:38 AM | ||
04-17-2024 02:11 AM | ||
04-16-2024 11:24 PM | ||
04-15-2024 12:25 PM |
User | Count |
---|---|
9 | |
7 | |
5 | |
4 | |
3 |