Network Security

I have entered the command;snmp-server host [interface] [i] community ANAME version 2cHowever, the pix still response to version 1 SNMP traps. How can i ensure that it only response to version 2c ?Cheers

Is there a way to change the native Vlan for an interface on an ASA 5510 running version 7.2(2). On each side of my firewall the native VLan is something other than 1. There does not appear to be a command similar to the native command on a switch wh...

We have an ASA 5510 running 7.2(1)24 and a Catalyst 3650 running c3560-ipbase-mz.122-25.SEE2.bin. I need to create trunks between the two, but so far I've had no luck.Here are the lines of configuration that have been added, but traffic cannot be pas...

I have a IDS 4235 with 6.0(2)E1 installed. However, I cannot update the Signature definitions due to there being no license key on the box. But I can't add our license key because there is no serial number listed in the config or through the IDM. Is ...

In the ASA ASDM, under VPN, IPSec, Tunnel Policy, if a transform set reads "not set!", does this mean it's not in use and can be deleted?

Hey all,I'm trying to configure failover on a pair of ASA 5510 firewalls. Both are running Security Plus Licenses. How I have know PIX and ASA failover to work is that each interface on both firewalls have addresses on the same subnet and the address...

I want to configure a PIX 501 firewall for NAT - or more accurately PAT.I want all inside users to be able to access the Internet using their non-routable IP adresses that the PIX will translate at the perimeter.I only have one public IP address avai...

I am trying to enable sylog logging to a Windows server thru my inside interface to beable to capture my VPN traffic. Everytime I enable logging my inside interface drops until I Disable logging. Please help, I'd like to be able to review all of my l...

Hello,I'm using a 2811 with one HWIC-2 DSL module, as router-firewall. I want a failover configuration,with Fa0/0 as primary WAN interface, Dialer0 as backup and one HWIC-4ESW (designed vlan1) as LANinterface. Fa0/0 has a fixed public IP, Dialer0 has...

HiI'd like to allow telnet access to ip 192.168.2.1 and 192.168.2.2 from our internal zone which has the ip range 10.0.0.0/8. Could someone please give me an example of how to do this, or point me in the right direction.Many ThanksDan

Hi ,Can anyone give me the Cisco TAC tollfree number,( I am in India) and proceedure to reach Cisco TAC through tollfree.I have raised teh TAC request for PIX firewall ,whcih has the SMARTNET CONTRACT with Cisco.It is very urgent.Thanks and Regards,S...

Hi all,I am looking for help in setting up address translation on an ASA (version 7.2) with the following scenario:-- four network interfaces: inside, DMZ1, DMZ2, outside-- inside and DMZ1 have limited number of subnets, DMZ2 has many subnets (routin...

DearI need to solve the below issue for which i need ur helpPIX with ISA in series to the inside interface .PIX inside ip 172.16.1.2/24 and the ISA server outside 172.16.1.1. ISA inside goes to the internal network where 5 servers are located to give...

Hi,I have some query regarding firewalling and GRE tunnel traffic.The quieries are like this1) Will I be able to inspect the traffic that is encapsulated on a GRE tunnel by putting a firewall (PIX or ASA) on the path of the GRE tunnel traffic.2) If n...