Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hi,Ihaev pix 506e runnig as my Gateway Firewall.Suddenly i am not able to Ping any interface,not able to telnet internal Interface.Internet Browsing also stopped .Can anyone plz tell me the causesa nd remedies for this.I dont have any Syslog Server e...

Hi,I have a Hub and Spoke topology, Frame Relay is the WAN connection.I'm planning to use EIGRP as Routing Protocol, but i'm stuck at the Firewall.I was looking for a way to configure the Firewall for EIGRP, which is think it supports just OSPF.My se...

I want to set up a mchine behind the firewall to be able to ping a outsdie computer. I looked at the cisco documentation, Handling ICMP Pings with the Pix Firewall. I configure every rule accordingly, and is not working.The icmp packet is going out, ...

eppiet by Level 1
  • 701 Views
  • 3 replies
  • 0 Helpful votes

Hi, A have an ASA5520, which was running with the image: asa704-4-k8.bin and the ADSM: asdm504-2.bin I upgraded the image in 7.0.5, and the ADSM in 5.0.5 The ASA boots correctly with this new version 7.0.5, but still boot with the ADSM asdm504-2.bin ...

croue by Level 1
  • 855 Views
  • 2 replies
  • 0 Helpful votes

We saw a couple of these yesterday. What concerns me is that the trigger packet does not contain a string that matches the regex. I have 2 questions:1) What is the point of putting brackets around the colon at the end of the regex? This is done in ot...

mhellman by Level 11
  • 623 Views
  • 1 replies
  • 0 Helpful votes

Hi All,I have upgraded our PIX from 6.3 to 7.1. But the PIX has stopped accounting VPN traffic.The command "accounting-server-group" is issued in the tunnel-group.In 6.3, I used the command below to enable accounting of VPN traffic. But this command ...

all clients asking for an IP address (via dhcp) get an address starting at 129.168.0.128 and up. i havent made any such configuration on the pix though. the DHCP pool we made is IPs in the range 192.168.1.50-100 (and 192.168.1.150-170 for VPN users)....

thomassadi by Community Member
  • 670 Views
  • 2 replies
  • 0 Helpful votes

Hi,A have an ASA5520, which was running with the image: asa704-4-k8.bin and the ADSM: asdm504-2.binI upgraded the image in 7.0.5, and the ADSM in 5.0.5The ASA boots correctly with this new version 7.0.5, but still boot with the ADSM asdm504-2.bin and...

croue by Level 1
  • 496 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Pix ddenly reboots

Our company has two Cisco PIX 525 Firewalls, one running as "active" andthe otherone running as "failover". The IOS in both of them is 6.1.1.From time to time one the Firewalls suddenly reboots (as shown fromthe syslog pasted in this message

jorantes by Community Member
  • 984 Views
  • 3 replies
  • 0 Helpful votes

I have a corrupt file system on disk0: since I did an erase command (I had to reload the .bin file to get back into the cisco# prompt) but now that it is loaded I cant access disk0: it says its Invalid.... I tried a fsck command to repair the file sy...

chrisbicm by Level 3
  • 3010 Views
  • 3 replies
  • 0 Helpful votes