Network Security

Engage with peers and experts on network security topics such as FTD, FMC, FDM, CDO and ASA.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

My company has not switched over to W2k yet. I'm trying to establish a VPN connection for our outside sales reps. Most of them are using either cable modem or DSL to get internet access. I am unclear on getting the VPN set up. Currently I have ou...

tmay by Level 1
  • 2000 Views
  • 1 replies
  • 0 Helpful votes

Hello,everyone: I have a question : How many access-lists can apply to a pix interface? I know that a router interface can only apply one access-list to it in one direction(in or out).

zoushan by Level 1
  • 1093 Views
  • 3 replies
  • 0 Helpful votes

Does anyone know of or heard of how to save the PIX config to a tftp server.Unlike the routers where you can directly save the running or startup config to a tftp server. Thanks in advance.

gspencer by Level 1
  • 1161 Views
  • 1 replies
  • 0 Helpful votes

I am trying to find a way to have multiple hosts inside a DMZ be able to access my entire internal network. Does anyone know of a way to do this without creating individual statics for every device that may be accessed?

collinss by Level 1
  • 1401 Views
  • 8 replies
  • 0 Helpful votes

I have a PIX 515 with inside, outside, and DMZ interfaces. I want to install a proxy server on the DMZ and have all my inside hosts go to the proxy first, before accessing the internet. If I don't want to configure a proxy-server address on each of m...

pambosch by Level 1
  • 1030 Views
  • 1 replies
  • 0 Helpful votes

Hi All, I put this thread in the remote access area as well because of the port I am having trouble forwarding through the PIX.What I'm trying to do is forward port 3389 (windows terminal services) to a W2k server. I tried using access list settings...

j.way by Level 1
  • 1093 Views
  • 2 replies
  • 0 Helpful votes

Hello,everyone: I have a PIX-535-R-BUN and a PIX-535-FO-BUN, I want to know whether the two pixs can configure as failover mode ? I read the doc of pix, It say that The PIX 515, PIX 525, and PIX 535 can only be used for failover if you have the...

zoushan by Level 1
  • 1044 Views
  • 1 replies
  • 0 Helpful votes

I have one PIX515 with two interfaces. In the inside interface is my Primary Domain Controller PDC with windows 2000 advanced server and in the outside interface are all my users running windows 2000. I have openened all the necesary ports in the PIX...

jmondaca by Level 1
  • 1424 Views
  • 7 replies
  • 0 Helpful votes

Hello,everyone: How can I distinguish the Unrestricted license (UR) and restricted license software? Is there any command to distinguish them? Another question is what is PIX-VPN-DES (56-bit DES IPSec software license for PIX)? Is it a piece o...

zoushan by Level 1
  • 1041 Views
  • 1 replies
  • 0 Helpful votes

I need to find out if subinterfaces are supported on the PIX firewalls. I am about to create a subinterface on my router due to non condiguous Class C IP ranges (can not do VLSM) and need to find out how the PIX will look at the different IP address...

bsaenz by Level 1
  • 1142 Views
  • 1 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card