Network Security

Dear All:I had ACS 3.0 it's for VPN client 3.5 authentication and authorization , i can authenticationsuccessful,But i couldn't authorization for VPN client,When i setting "downloadable PIX ACL",as bellow is my definitionpermit tcp any host 192.168.5...

I connect successfully to my PIX 515 ver 6.2 with my 3.5 client but i generate a 1 18:29:28.218 07/16/02 Sev=Warning/3 IKE/0xA3000057Received malformed message or negotiation no longer active (message id: 0xABF21F4A)and I cannot ping or access anythi...

TAC changed my config for my Pix 520 when I upgraded IOS from 4.3(2) to 6.2.1, and now these programs no longer require the user to be authenticated through CS ACS before they can logon. Browsers still require authen though?? Anyone have a start plac...

I am setting up a 501 for (small office, I'm a volunteer) security and remote admin. access behind an "Efficient Networks" Speed stream 5861 static DSL router. How must I config the outside port address of the PIX to enable access by me from the inte...

coule the pix change source and destionation address to another sour. and dest. ip address when ip packet pass the pix firewall ?for example :sour. 10.1.1.1 / dest. 10.2.2.2 --> PIX --> sour. 172.1.1.1 dest. 172.2.2.2 how could i do if could ??thx...

I have internal LAN behind my PIX firewall with 6.0(1)...My real player installed in the internal LAN aI need to allow the outside users to access and run the real player...My PIX conf.as the following:fixup protocol ftp 21fixup protocol http 80fixup...

Just looking to set up the console port password on a pix 501 running 6.2(2).Also can I put a timeout on this port.ThanksPat

I'm looking for a way to let our PIX 525s (running OS 6.2(1)) use a select global range of addresses when the users in our network are trying to reach select external sites.Situation:On the inside interface we're using 10.194.134.0/23- When trying to...

hi allis it possible to configure pptp between a pix 6.2 and a ras server windows2000 (not a nomade pc client)cisco give the following conf for a clientsysopt connection permit-pptpvpdn enable outsidevpdn group xx accept dialin pptpvpdn group xx ppp ...

Hi Guys,Does anyone knows how to configure the Pix HA site-2-site failover without the Serial cable. I read this is a new feature in 6.2.1 but I can't find any documentation on how to configure it.Thanks Gonzalo

How do you set up multiple Pix firewall to send their syslog data to a single Syslog Server and have a differnet directorys for each Firewall. I currently have one file by Day for serveral firewall's.

Hi Guys,Does anyone knows how to configure the Pix HA site-2-site failover without the Serial cable. I read this is a new feature in 6.2.1 but I can't find any documentation on how to configure it.Thanks Gonzalo

Hi,I'd like to understand how PIX goes about applying rules on an incoming packet? Is the first rule that matches the packet description applied or does it go to the end of the rule base before making a decision?Does PIX do any rulebase optimization ...

I have setup a pair of PIX(failover). I have no problem ping across the firewall to remote subnet. But When i try to ping within the same subnet, it fails.When I do show arp on one of the machine. The mac addresses of the machines in the local subnet...

Hello to all the specialists I have pix firewall (515 with ver 5.2)I need to know how I can connect with secure remote To the pix while the client is sitting on nat network (For example adsl network or a hotel)I have the old vpn program safe net and ...