The diagnostic interface is reachable over a VPN tunnel by our NMS server (can ping and ssh into it), but the firewall (ASA 5508X running FTD 7.0.1, managed mostly by CDO except for SNMP and DHCP relay (argh!!)) isn't responding to SNMPv3 queries - ...
Forum Posts
It appears this particular firewall is not acknowledging the last rule prior to default action. Its the only firewall in our fleet ignoring that rule. I test all other firewalls and confirmed they are matching. I made sure the zones are applied to in...
I have an FTD 1010 with only a base license and a requirement to use this as a simple Internet router/gateway. I have a dynamic NAT rule using interface PAT and one access rule that trusts outgoing traffic. If I set the default action to block I ca...
HelloI would like some guidance on my new Firepower 2110. This is out of the box.I would like to run ASA on this device as platform mode and upgrade it using. The Firewall currently has the default software 6.2 installed. I tried uploading a package ...
Resolved! FTD NAT to Exchange server help
I am banging my head here trying to figure out why I can't get Exchange email to flow. I have this same setup at a different site with no issues. I have the settings mirrored to this new site and Exchange email will just not flow. I currently have ...
I have a stand alone FTD that is remote with its only connection to the DC is via Site to Site VPN on the "outside" interface. I read where the version we are running supports using the data port as the management port, but I can not find any detail ...
Resolved! remote SSL VPN
dear Gentscould you please support I am using ASDM for ASA and I have privileges' 15 but once I access ASDM I can't see any tab for remote VPN or even I can't see it in VPN wizard I try to check in options but nothing , kinky refer to image in attac...
I was wondering if there is a way to automatically block IP addresses depending on traffic analysis. I see a number of attempts from an attacker and see the traffic is being blocked on the attempt but I would like to impose a temporary block on any ...
Resolved! FPR1010 can't access *SOME* web sites
Hi all, I have run in to a weird issue with the FPR1010. When connecting a client machine to the inside network, I can browse some but not all web sites. The particular problem is my 'test' site of www.bbc.co.uk. However, rather unbelievably, it will...
Hi Accessing to a router (7200/ios15/192.168.1.16) from Ubuntu via ssh failed as below. It looks like there is no matching cipher. After several tries changing different cipher as below, ssh still cannot access the router. Anyone can share some solut...
Hallo , I am tracing from outside to inside with the following config but am not able to trace it from outside, but it is working from inside-Outside. class-map inspection_defaultmatch default-inspection-trafficclass-map TRACE-Cmatch port udp rang...
hi,i got a pair of ASA active-standby pair which failover didn't work or kick in over the holidays.the traffic was restored when manually forced a failover to secondary FW.failover link is via port-channel 1 and "data" ports are in a port-channel 15....
Hi, I have a device in my DMZ that needs to talk to my inside network server. I can't telnet using the ports that I have listed in my access list. Packet tracer shows that the TCP traffic is not blocked from the inside to the DMZ1. packet-tracer inp...
Hi We can define ssh version 2 at router or switch with command ip ssh version 2. but we also can see Openssh 7 that people talk about. Is there any relation between ip ssh version 2 and Openssh 7? Thank you!
interface outside: Static PAT, Static NATnat (any,outside) source static NAT-Private NAT-Publicobject network PAT-Privatenat (inside,outside) static interfaceinterface inside: with Dynamic PATobject network INSIDE-NETnat (inside,outside) dynamic inte...
