Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hi ALL Any option to enable stun protocol inspection for specific rules only in FTD2110If not do we need to enable it in global policy ... what are supportive commands to enable this protocol This is what we see atm > show service-policy inspect stun...

TJ01 by Community Member
  • 4544 Views
  • 5 replies
  • 0 Helpful votes

Hello, Exploring port-channel configuration on the firewall for redundancy but to my surprise, it not supported on FTD running version 6.3.0-80. require FMC to do it.https://www.cisco.com/c/en/us/td/docs/security/firepower/630/fdm/fptd-fdm-config-gui...

owen2 by Level 4
  • 1724 Views
  • 1 replies
  • 0 Helpful votes

Hello, I have a customer that has a few ASA5510 in their environment.  I realize these were end of support back in 2018, and have also read that the last software version supported on the platform was 9.1.x.  Can anyone point me to information about ...

I have a pair of Cisco 2100 series firepower devices that I am configuring for deployment at two separate locations. Currently when powered on, they go into rommon, without any prompt from me. Once I type the boot command they will complete their boo...

cgedwards by Level 1
  • 14390 Views
  • 5 replies
  • 0 Helpful votes

my post marked as spam i dont know whyi am doing a lab with packet tracer and i cant reach inside network to dmz asa config  hostname ciscoasanames!interface GigabitEthernet1/1nameif dmzsecurity-level 50ip address 172.19.3.1 255.255.255.252!interface...

adel85 by Level 2
  • 1775 Views
  • 3 replies
  • 0 Helpful votes

Hi Teams, Firepower have URL filtering function.I have some questions about this.Q1) Firepower support URL restrict(filtering) option without Category license(In ACP rule). What is difference this URL restrict and URL filtering(use C License). Q2) As...

HWAN by Level 3
  • 4052 Views
  • 2 replies
  • 0 Helpful votes

I have 55 users connect to two switches each switch has two cables each one for a Different FW one FW for VPN and one For Internet, ( each one also BKP for other ) each FW has one Cables to Provider other Site has one FW only now : between Switches a...

Hello guys, I am following an online course with FTD and FMC. when I try to add my FTD to FMC I get en errorCould not establish connection with Device Possible reasons could be:- - Time on FMC and Device are not in sync. Make sure NTP is configured o...

Hello All, I cannot ping any external DNS servers like google (8.8.8.8)  or comcast (75.75.75.75) or cloudflare (9.9.9.9 or 1.1.1.1) from a PC (192.168.1.5) on the inside interface of Cisco ASA 5506?I have tried packet tracer and it states its allowe...

JJevans_2112 by Community Member
  • 5266 Views
  • 3 replies
  • 0 Helpful votes

Hello everyoneI have a weird problem with configuring SSL inspection In Cisco FTD , every time I enable SSL policy In ACP  all ssh session that go through FTD will be drop after 10 to 20 seconds .even configuring  all SSL Rule to do not decrypt still...

ahmadtec9 by Community Member
  • 2611 Views
  • 5 replies
  • 0 Helpful votes

Hi All, Im trying to reach ip (10.100.20.66) hosted on cloud but not able to achieve it. Attach is the Error im getting if i do packet-tracer. Below is my packet-tracer command.  Can anyone help me to resolve this issue packet-tracer input inside tcp...

sv7 by Level 5
  • 1654 Views
  • 4 replies
  • 0 Helpful votes

Hi Folks, I have a situation where I need to change my standby firewalls MGMT interface IP via Primary one.My secondary is up but not reachable for SSH due to service providers IP conflict.1. Is it possible to do so ? or shall I need to arrange an en...