Upon boot the LED indicator for WiFi on this ASA-5506W cycles through blinking green to blinking red. The documentation says it means "Ethernet link not operational". Since this is a hardware addon, I assume ethernet link is hard wired inside. To mak...
Forum Posts
Hi,we have a FMC ver 6.3.0.3 and FTD 5516-x both have been workingCurrently FTD is working with 4 interfaces (outside,outside2,inside,LAN-B,LAN-c). LAN-B and LAN-C are the new interfacesFor hosts the default gateway is a router that also hande MPLS c...
Resolved! GRE Tunnel (Packet Tracer Bug?)
Hi Guys, i have some issue with GRE Tunnel in Packet Tracer during my Training.. all the setup is correct, both tunnel is up/up, but i dk why it just cannot go like 192.168.1.2 -> 192.168.25.2 -> 10.0.0.2
I am trying to push software update to FTDs from FMC FMC running 6.6.1 version and same version trying to push on FTD but it gives error message. Pre upgrade validation - snort version on device is out of date. Deploy access control policy from FMC ...
Resolved! Firepower Sensor Upgrade from FMC
Hello Current SFR version on ASA is : 6.2.2-81 Our FMC version is : 6.2.3.5 I am trying to push Sensor update (6.2.3.5-52) from FMC to ASA Firepower Sensor, it says "No valid appliances available for Cisco Network Sensor Patch 6.2.3.5-52 This u...
My project is to connect a firewall WAN interface to Cisco Prime, I should keep tracking the interface utilization on my firewall until it reaches a specific bandwidth. when for example the bandwidth reaches 30 Mb, I want to receive a notification or...
We created rules to block inbound and outbound traffic using a geolocation object. Both rules were at the top of the ACP, and were basically inverse of each other. The rules were set up as follows:-----------------------------------------------------...
Resolved! ASA NAT Configuration
Hi all, I have an ASA 5525x with PC-A on the INSIDE network with IP address 10.20.32.40. PC-B is in DMZ with an IP address of 10.20.30.10. The security level for INSIDE is 100 and DMZ is 50. I have rules to allow PC-A to communicate with PC-B over...
Resolved! FMC/FTD
HiWe have FMC 100 and FTD 2130, when I do a packet tracer on the device its saying traffic is allowed but I cant find the ACL on the ACP that would allow this traffic, its almost as though there is an hidden ACL which is allowing certain traffic whic...
Hi Team,I wanted to make you aware that we will have a series of monthly 30-45 minute technical webinars regarding the migration to Snort 3 This is highly relevant for ALL FirePower customers. The content is technical in nature and is designed to all...
Hi, This is my first post, I have a Cisco Firepower Chassis 2110 with Virtual ASA running on it. I am trying to only get the Syslog or realtime logging for any users logging in directly to the Cisco Firepower Chassis 2110. Can someone help with this...
Cisco Firepower Threat Defense (FTD) is an integrative software image combining CISCO ASA and FirePOWER features into one hardware and software inclusive system. wich can be managed through Cisco FMC a single management console to manage an entire pl...
I am trying to upgrade the ASA from 9.13 to 9.14 but I get the attached errors, can you help me with that?
HI Team , i have forget the one time registration key used which was used to build the Cisco FMC HA configuration. can someone help me on this to recover the registration key . ThanksPrasaath D
Hi ,I have mid size network for which I am planning to buy virtual FMCs as the physical FMC1000 that we have is going to be EOS soon. I have a pair of 4110s at edge and one 2110 for testing. I am going to add a pair of 4115 in the DC. I do not have I...
