Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hello all. We have a customer who upgraded the FMC upgraded from 6.6.0 to 6.6.1 successfully.Ithen to upgrade the FTDs from 6.4.0 to 6.6.0 but hit an error which states Update to install failed. we are both new to FTD, whereabouts can we see more det...

lowfell by Level 7
  • 3472 Views
  • 3 replies
  • 0 Helpful votes

So this is a LAN setup & using GUI but can also use cli if needed.Ive been troubleshooting this for a few days and I think FTD is blocking the access between the port 3 and port 1.Here´s the setup: Host - 192.168.3.5/24FTD Port 3 - routed status - 19...

S3C by Level 3
  • 9104 Views
  • 13 replies
  • 0 Helpful votes

Hi, Is there a way to filter logging output to a specific interface on the Cisco ASA ASDM? I have tried the ASDM Logging Filter under Monitoring->Logging->Real Time Log Viewer However with this tool you can only define limited parameters like "Source...

Letau Matlou by Frequent Visitor
  • 2041 Views
  • 0 replies
  • 5 Helpful votes

i want to have a setup where ASDM users have a second factor before having access to the firewall. kindly assist if anyone has done anything similar.

Hello,I have switched configured with 802.1x to run as authenticator.In one of the ports I would like to add Cisco ASA as supplicant and keep 802.1x enabled.So the question is , can I add a username and password on the ASA so it will authenticate its...

Hello All, I have a customer who wants to stay on the ASA platform but needs to support more throughput.  I thought about ASA on Firewpower.  I could install the ASA software on a 2110 for 2.3 Gbps of throughput or a 2140 for 9 Gbps of throughput.  I...

robinson by Level 3
  • 1894 Views
  • 2 replies
  • 0 Helpful votes

Hi, we applied the FTD update version 6.4.0.10-2 to patch the recent Cisco vulnerability and after it was done, I went back into the updates just to verify they were all applied. To our surprise, both FTD appliances, are still on version 6.4.0.9-62 e...

Hi, anyone here experience to access their ASA firewall (ASDM/SSH) from the inside interface but the user is coming from outside interface of the ASA? I see some use cases using management-access but it uses VPN tunnel, can it be done without using a...

Hi all. I'm new to the ASA devices. I have an ASA5512 plugged into a business router trying to get VPN access to a secondary network. I cant seem to get the anyconnect web launch to be found. is what i'm trying to do even possible. The last time I se...

Matt_Bell by Community Member
  • 1545 Views
  • 1 replies
  • 0 Helpful votes

Okay so I have an old SG 200P.   It was installed years ago and there are is no knowledge of credentials and no known config file.   Here is what I have:1. SG 200P that will power on and LED lights on ports when things are plugged in BUT no SYSTEM LE...

gocaps25 by Community Member
  • 2443 Views
  • 3 replies
  • 0 Helpful votes

Hi,I have been trying to figure out if I need to upgrade my ASA firmware version, but the more I read the more confusing it starts to get.I have two ASA active/standby firewall pairs - A pair of 5525-x and a pair of 5506-x The 5506x are running ASA v...

nxw1969 by Frequent Visitor
  • 3369 Views
  • 6 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card