Hi, we applied the FTD update version 6.4.0.10-2 to patch the recent Cisco vulnerability and after it was done, I went back into the updates just to verify they were all applied. To our surprise, both FTD appliances, are still on version 6.4.0.9-62 e...
Forum Posts
Resolved! Management-Access in ASA
Hi, anyone here experience to access their ASA firewall (ASDM/SSH) from the inside interface but the user is coming from outside interface of the ASA? I see some use cases using management-access but it uses VPN tunnel, can it be done without using a...
Resolved! Export syslog settings from ASA to FTD
Hi Is there a way of exporting the syslog settings (syslog id, syslog level and enabled/disabled) from ASA to FTD?I'm looking at a daunting task with plenty of hours of manual labor if not. /T
Hi all. I'm new to the ASA devices. I have an ASA5512 plugged into a business router trying to get VPN access to a secondary network. I cant seem to get the anyconnect web launch to be found. is what i'm trying to do even possible. The last time I se...
Okay so I have an old SG 200P. It was installed years ago and there are is no knowledge of credentials and no known config file. Here is what I have:1. SG 200P that will power on and LED lights on ports when things are plugged in BUT no SYSTEM LE...
Resolved! ASA Firmwares explained
Hi,I have been trying to figure out if I need to upgrade my ASA firmware version, but the more I read the more confusing it starts to get.I have two ASA active/standby firewall pairs - A pair of 5525-x and a pair of 5506-x The 5506x are running ASA v...
Resolved! Anyconnect client upgrade on FTD
Hello guys,I am going to upgrade Anyconnect client software on FTD using FMC.My question is when the anyconnect client software is uploaded, what happens?- Is anyconnect client software on user side going to be upgraded automatically?- Should user go...
We have purchased two ASAv 10 appliances (virtual) and I have the RTU notification. Product Name is L-ASAV10S-K9=, states eDelivery and shows SO#. How do I associate this to my CCO account so I can download the appliance and use? After I download...
Hi Team, I have device FPR 4110. Running 6.1.0.330.cfp Type FTD (if using GUI) but when I SSH device. show version : System version: 4.0(1.140) and FMC running on 6.2.2 as below.. my question is,How to upgrade version FTD(Device) and FMC ...
Hello, I have a system with an ASA that has SFR managed by FMC.I have an issue with the uploading of 6.6.1 update file to the SFR from FMC. I get the below on the message center: Update PushPush to 'name of the SFR'Error copying file remotely: State...
Is there a way I can create a report template in order to export Cisco Anyconnect client history info? Mostly, we just need to know when the client connected and the duration of the connection. I can pull up this info in real-time from the ASA, but...
Hi, Do anyone can help how to troubleshoot why the static NAT setup not work ? How to issue debug ip nat on ISR4331 ? Router A1 Configinterface GigabitEthernet0/0/0ip address 172.25.251.30 255.255.255.224no ip redirectsno ip unreachablesno ip proxy-...
Dear support team,I have a requirement to allow only windows update from specific IP address to the internet. The firewall we use FTD1010.we used below link as reference for the URLs and ports to be allowed for windows update.https://answers.microsof...
Resolved! Anyconnect APEX license Issue
Hi Support, Our order is L-AC-APX-LIC= for an ASA vpn anyconnect 110, as indicated in attached screenshot And I downloaded the license from the portal and i install it on ASA, but after reboot and "show version" command, it shows me that we have 50...
Hello, After associating a FIrepower (2100 series) with a FMC (version 6.4.0.4), dashboards are showing no data. We have verified that IPS events are being generated and sent to syslog but the FMC shows no record of any events being generated. We als...
