I bought a 5506-x to learn it but the only thing I'm learning is that its becoming a pain to do the things I want to do. I am trying to create a VLAN which is supposed to be created by making a sub-interface. I have setup the configuration several ...
Forum Posts
We are in the process of replacing our remote ASA 5506X devices with the new FPR1010 devices.Our FMC at the main office manages all of these devices with classic licenses.I know the new FPR 1010 devices require a smart license.Is there any issue runn...
Hello, I have an issue, the FMC GUI is too slow (unusable), cli works fine, the health monitor of the FMC gives me this message: The intelligent platform management interface daemon exited 8 time(s) The first events after a reboot: The remediation da...
Hi Everyone, I remember from my first deployments of FMC1000 and FMC2500 that CIMC is installed but not supported, I would like to know if recently this is changed and if there is eventually any option to use CIMC with FMCs. We have an OOB serial con...
Due to a bug (CSCvq71351) in 6.4.0.7 - inline sets must be deleted/recreated if they need to be edited Is there any potential traffic impact in deleting/recreating an inline set - as long as you don't push policy until after the inline set is rebuilt...
Hi forums, I recently discovered a strange phenomenon on one of our managed ASAs that I couldn't quite figure out. * Hardware: 2xASA5545 running AS OS 9.8(3)29* uRPF ist enabled via 'ip verify reverse-path interface <if>'* cluster protocol packets ar...
Resolved! ACL not showing in ASDM 7.1 (ASA 9.0)
Hi all,I've configured a couple of ACL rules via CLI in my ASA.When i checked in the ASDM, it only shows the basic rules that was configured by default and did not show the rules that i've created.Anyone else facing the same problem?Thank you
Hi Guys, I need your help for my problem, I have ASA5516 on active and standby. We already upgrade the IOS version to 9.5(1) both but sometimes ASA devices which as active mode change the IOS version to 9.8(2). This the error messages : ************W...
I have a 5506-x asa and im trying to segment my internal network into several "zones".For example:192.168.1.0/25 LAN192.168.1.128/25 WIFI LAN192.168.2.0/24 IOT192.168.3.0/24 LABI have the base license and can create a max of 5 VLANS I don't know if I...
Do we need to enable aaa for serial login?.Currently I have not enabled and it's blank, when I queried the cisco tac whether not having a aaa config for serial cable while having it for others such sab and ht woud work he said. He said when I connec...
Hi,I would like to ask about to allow essential port on firewall to secure.I saw essential port to open for active directory service as below .RPC endpoint mapper: port 135 TCPLDAP: port 389 TCP, UDPLDAP over SSL: port 636 TCPGlobal catalog LDAP: por...
Hi team, I'm simulating packet tracer before putting my FTD on production: But when sending a packet from a Lan machine to google : I get always this result : Result: input-interface: inside input-status: up input-line-status: up output-inter...
We deploy ASAv50 version 9.12 but I found ASAv50 display failover state difference CLI with ASDM. CLI Display : Active/ActiveASDM : Active/Standby Please suggest me .
I currently am using a ASA 5510 Firewall and ASA 5516-X, by defaut what security settings aren't enabled that I should have enabled in any network configuration? Also, by Default is IPS/IDS enabled or is this something that needs to be configured? An...
Resolved! FTDv w/FDM smart licensing question
Hello all. I have a client who requires an air-gap FTDv deployment. They are using FDM for management. This client cannot use a satellite server, they don't want any communication over the Internet. I know that software version 6.3 provides an air-ga...
