Hi,I have built an FTD 750 but not added it to the FMC Manager yet. I only did the interfaces and the routing table. I still have the default mgt interface of 192.168.45.45 But now i cant log back into it on the webpage. I am getting these errors...
I use WCCP to interact with my IronPort web filter. Currently my WSA (web filter) sits on my inside network. WCCP is configured to redirect inside traffic to the WSA off of the inside interface. It is my understanding that my ASA (8.2) can not red...
Hello Everyone, I need suggestion , I am trying to configure IPsec VPN with failover. The scenario ,I have two firewalls with Active/Standby configuration. I want to configure 2 VPN's from firepower to different remote peer IP address . If primary ...
I have the following setup: [client 10.1.20.0]---inside--[asa fw]-outside------[server 192.168.0.0][client 10.1.30.0]-----inside--^ Essentially two separate networks connected to the asa firewall on the inside and one on the outside.The 10.1.30 subne...
Hi, Does anyone know what does the known affected release for the bug CSCvq07297 means? Is it referring to the Snort Version? The link to the bug is as below:https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvq07297 Thank you in advance.
Hello,First, I'm not an expert in networking, I am a sysadmin.I have an access to our cisco ASA via ASDM GUI (v7.8). I have 2 servers on private network (same subnet, serv1 192.168.0.1 and serv2 192.168.0.2) and 1 IP on public network (say, 18.18.18....
I'm using the 6.2.3 vFTD OVA provided by Cisco. I want to manage it locally, not with an FMC. After setting it up in vSphere I am able to ping other devices on the network but am unable to access it via SSH or HTTPS. It just times out. When I do "sho...
Hello We are planning the migration of an ASA5540 to a Firepower 2110.The new implementation will use AnyConnect for remote access and ISE will be used as RADIUS server.The module NAM in anyconnect is compatible with Firepower versión 6.2.x? Accordin...
hi,i need to lock down SIP ports on an ASA FW towards our internal SIP/voice GW:external SIP 208.x.x <> ASA FW <> 66.x.x.x internal voice GW per my google, SIP is TCP/UDP port 5060 but i can see some had 5061.there's also the dynamic/ephemeral po...
Hi, So I was upgrading an ASA 5506-x from 9.9 to 9.10 using the "Tools / Check for ASA/ASDM updates..." function of the ASDM launcher. It found the 9.10.1 update, but then a message box popped up: "Module Firepower is not supported on this plat...
Hello, everybody! My question is very simple: Are there any other methods for load balancing on ASA 5525, except this?https://supportforums.cisco.com/t5/security-documents/loadbalancing-dual-isp-on-asa/ta-p/3127108 So, If I have 4 ISPs, should I spl...
Good day,I am a security analyst trying to tame the log traffic from our firewall (2 FTD 4140 + FMC). I have had a CCNA in the past but primarily worked in systems so I am familiar with networking protocols and concepts but inexperienced at troublesh...
I have 2 new FPR-1010 According to the documentation, on the first boot, I should get a EULA prompt and then a "Manage the device locally? (yes/no) [yes]: no"https://www.cisco.com/c/en/us/td/docs/security/firepower/quick_start/fp1010/firepower-1010-g...
We have two Data Centers, East and West. The West is considered our DR site (separate, but identical Hw). If the EDC data center craters, we would like to spin up the WDC using the EDC's Master System config.Currently we are using a tool to pull th...
Hello all,I have what I think is a fairly simple question. Will adding stateful failover to an already existing failover HA pair on the ASA disrupt any services on the firewall? I was looking at the failover pair and noticed that the 'failover link...
