Upgrading a Cisco 2500 to 7.4.0.118 using below guide.https://www.cisco.com/c/en/us/td/docs/security/firepower/fmc_model_migration/b_FMC_Model_Migration_Guide/m_fmc_migration_workflow.html#id_111621Been upgrading for over an hour now how do I view th...
Does it really matter which port you enable on a sensor/FTDv (managed on FMC) for passive monitoring? So as long as say SPAN port is configured on the device/switch to send traffic to the the server port that the FTDv host resides on you should see t...
I have a Cisco Firepower 1010 that I am trying to connect to a ubiquiti network switch that is configured for 3 vlans, default 1, 120 and 130. I have configured the same vlans on the Cisco Firepower 1010 and have setup DHCP servers for each vlan. I...
Hello,I am running Firepower Virtual appliances in AWS. They are behind a GWLB and all part of a target group. The appliances were running 7.2.8 and we updated to 7.4.2. We removed an appliance from the target group, updated the software, and then pu...
need to know the replacement for Cisco Firepower 4110,also, does the Cisco Firepower 4110 Series include (4110, 4112, 4115, etc. ?thanks
Trying to setup a remote storage for cisco FMC 2500 getting the error below. I have double checked the credentials but unsure on the path. I would like the files to go to the d:/
A newer version of Firewall Migration Tool - 7.7 is now available for download. Along with the bug fixes, this new version comes up with the following new enhancements. Support migration from Cisco Secure Firewall ASA to Cisco Multicloud Defense Sup...
Hi, I'm currently unable to connect to the standby ASA using ASDM or SSH. I can connect to the active ASA through the outside interface without any issues. However, as part of the ASA upgrade process, I need to access the standby unit via ASDM, but I...
Actually, I want to allow FTP from outside to inside, but the packet tracer display "Drop-reason: (acl-drop) Flow is denied by configured rule". I must be wrong something. I have attached my config. Any assistance would be greatly appreciated.
How do I implement the Failover license function under FPR1010-NGFW-K9? Do I need to buy a license? Or does it come with the relevant subscription?
I have a Nexus 5k with a 10k sfp configured for vlan 800 along with another port also configured for 800. This goes into an edge router which then goes into the outside interface of an asa 5545 (had to do it this way temporarily because I did not h...
Hello everybody, I have been tasked to upgrade a HA pair of two FPR-2110 running rel. 9.18(4)22. I checked the upgrade guide (see screen dump attached):https://www.cisco.com/c/en/us/td/docs/security/asa/upgrade/asa-upgrade/asa-appliance-asav.html#id_...
Hi,The recommendation for failover link between two firepower devices in active/standby setup is to be the same bandwidth as the data interface.The Firepower 1150 has only 2 x 10 Gb/s SFP+ interfaces, the rest are 1 Gb/s. When using the two 10 Gb/s a...
OK for the life of me, I cannot figure out how to route VLANs so that they have Internet access. Whether I choose Access or Trunk, I simply cannot get it to work. Online searches turned up absolutely nothing, not even the Cisco documentation could ...
We have two data centers HO and DR. We have VPN firewalls in both data centers and we are planning to purchase certificates to use for Anyconnect in these firewalls. I know that we can use SAN names in a single certificate (like ho-vpn.domain.com and...
