Enabling our customers to leverage their install base and take them to the next level with Cisco Secure Firewall Threat Defense has always been a key priority. The migration tool is available for download to migrate the configuration on the on-premi...
Forum Posts
For some context, we have dual Firepower 2140s in HA managed by FMCv. Both FTD and FMCv are on 7.2.5.1 as of last week at the start of 2024. We currently utilize our FTDs as external firewalls and head-ends for both site-to-site VPNs and Remote Acces...
I am unable connect to the Cisco ASA 5506-X with putty but I'm able to connect to the old ASA 5505. Recently, we replaced our ASA 5505 with 5506-x and whenever I try to connect to the new ASA I got this error message" Selected host key algorithm does...
Hello!I want to implement this network with the technique router on a stick to perform intervlan routing.The first router connected to the ISP will be the edge routerThe firewall is ASA 5505The second router will be the internal routerHow do i imple...
Hi All, I heard that there is a 90 day evaluation copy of FTD you can get from Cisco. But look like when I tried to access Demo License Section with my Cisco ID it is giving some error related to my id is not associated with required service contr...
I'm having a strange problem with an ASA. Its a pretty basic setup with a FPR-1010 running an ASA image (version 9.18(2)). I have webvpn configured, but disabled right now for troubleshooting. The issue I'm having is that no matter what access-list i...
Hello everyone,I did spend quite a bit of time searching for the MTBF for the FPR1120 Firewall with the ASA Image but couldn't find it yet.Does anybody have an idea where to find the MTBF for that device? Thanks and all the best kurt
Resolved! Is FTD’s control plane wide open?
I was looking into setting up BGP on an ftd and was wondering where to allow TCP179 and then I realized there is nowhere to even add this as an access entry. Same goes for VPN. Is this not wildly insecure?
Hello, I am using Cisco Firepower 4112 Threat Defense v7.2.4. I have to configure 5 syslog servers, will this cause any performance issues?Note that I send with port 514 UDP and through management inferface.
Hi guys, I have this issue for a long time now. We have two pair of FTDs in HA in two different DCs. We have VTIs setup in both HA pairs going to each remote site. This case have been with Cisco TAC for a long time and we still not get to the real pr...
Dear Team.I have a Cisco ASA 5506. We have several internal servers that require public access. In addition, we have purchased public IP pool from our Internet Service Provider (ISP).Currently, we have one WAN ip assigned directly to our WAN interfac...
Hi All, I am currently configuring a 5506-X for my home network. Currently, I can ping outside IP addresses, but cannot browse to any websites. Browser messages like "Can't reach this page" or "took too long to respond". DNS is configured, NSlookup ...
Hi All,Can we integrate FMC/FTD with DNAC?if yes, What are the benefits?
One of our FMC's is not providing a Notes popup field when issuing a deployment.We use this Notes field to enter our change# among other things. Where is the setting to enable this popup?(I now had to go into the Deployment history to update the Note...
Hello everybody,our customer has a Firepower 1010 running with ASA rel. 9.16(2)14(appliance mode) and is registered in the Smart Licensing.I want o upgrade it to the sugg. rel. 9.18(3) from the USB port.I went to the fx-os level as usual, but I did n...
Hello,we would like to access ASA1`s management01 Interface IP (192.168.4.1) from a host behind ASA4´s Interface GigabitEthernet0/1.1 via ASDM.The flow is SRC: 10.10.10.5 DST: 192.168.4.1 Port: 443 & 22 (ASA4 > ASA3 > ASA2 > ASA1)On ASA1 in the pack...
