Hican I get advice about error log:%ASA-6-303014: Teardown TCP connection 100668898 for outside:999.999.999.99/47336 to inside: 888.888.888.88/1531 duration 1:00:00 bytes 5240 TCP Reset-O%ASA-6-302014: Teardown TCP connection 47476333 for outside:999...
We have recently purchased a Firepower 4110 to replace the EOL IPS on the 5585-x series. I understand that you can create a logical device with either the ASA or FTD image. My question:If you install the ASA image rather than FTD do you have the IPS ...
Hi all, I have an ASA L2L ASA connection (including VPN Dial-In on both ASAs) up and running. Additionally Internet connection works fine. LAN 1----- ASA1 --------IPSec-VPN-L2L----- ASA2 ----- LAN 2.All works fine.Now I added a cisco 2960-x switch wi...
Dear All,I would like to request to help and find out my network problem.I have one server and one NAS and network connectivity as below design.I am using cisco switch,juniper srx and junos e4300 switches.My first question is my design is correct or ...
Hello what are the steps to activate a new ASA 5506-X ?Does the ASA need to be activated before you can start initial configuration?
Hi community, We are experiencing an issue with regards to a specific flow we are trying to permit through and then back in through the ZBFW we have deployed. The flow is defined below. The flow is slightly unusual in that we are using TCP traceroute...
Hi, Our Firepower management system is reporting several error messages on one of our remote sites in Japan, where we have an ASA5525. The first error message was also reported in our office in Brazil, but it was resolved by re-seating a loose cab...
Good day, I just started a new 5506 ASA (HW v01) and it instantly stuck in an endless reboot cycle.As it seems, there is an invalid image on the ASA: rommon 2 > dir disk0:File System: FAT32drw- 3 0 .privatedrw- 4 0 ....
Hello, I have a problem to boot this ASA5506, got errors that not sure how to fix this, any idea?? Cisco Systems ROMMON, Version 1.1.8, RELEASE SOFTWARECopyright (c) 1994-2015 by Cisco Systems, Inc.Compiled Thu 06/18/2015 12:15:56.43 by buildersCurr...
Good day; Need help seeing what I am not seeing at the moment. I have built a l2l to the AWS cloud I run a packet trace outbound and that passes but when I run packet tracer outbound in I keep getting denied by Implicit rule. I have gone over my con...
GreetingsI have a case where I need to have a lower ARP timeout value than the default 4 hours on one of my FTDs running 6.3.0.3. Under platform Settings there is an ARP timeout that the manual even at 6.4 says is "transparent only" which is not the ...
Hello Everyone, I am having some issue with my ASA 5506-x. Inside: 192.168.0.0/24outside: DHCP(let's say 10.0.0.1/24)Network object: 192.168.0.246 I open port for RDP to remote in from outside to inside for my network object NAT rule and create acce...
Hi all, I'm testing a new lab with FMCv and FTDv on 6.3.0-83 and having Management IP setup issues on FTDv. Followed the regular OVF deployment and setup on 1st login but cannot get fixed on interface. Tried to update se configure network ipv4 a...
Hi I don't have "ASA FirePower Configuration" menu in ASDM. I have already configured IP to management 0/0 port 10.226.24.181 also to SFP manager 10.226.24.130. I can ping 10.226.24.130 from ASA CLI and have tab in ASDM (with https://No DC Configured...
Hi All,in document 'Cisco ASA 5500 Series Configuration Guide using the CLI' it mentioned, If a unit boots and detects a peer already running as active, it becomes the standby unit.My situation is FW1 is set as primary, FW2 is set as secondary. When ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 08-10-2026 08:58 AM | ||
| 08-10-2026 02:48 AM | ||
| 07-22-2026 05:00 AM | ||
| 07-16-2026 06:39 AM | ||
| 07-15-2026 08:48 AM |
| User | Count |
|---|---|
| 4 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
