We have a firewall that was purchased a few years back and we are trying to figure out if it is TAA compliant. The serial number of the unit is USE111NBQZ.
Forum Posts
I am configuring always on VPN with TND on a Cisco ASA 5508, the client downloads the profile correctly, and correctly recognises when it is on a trusted network, however when we move to an untrusted network I get the error "anyconnect cannot confirm...
We've a customer who wants to deploy some vFTDs in AWS with auto scaling, most of this is ok but I'm stuck on how we monitor (ping, SNMP poll / traps & netflow) firewalls which both:Allocated IP addresses using DHCPAre auto created by scripting, so t...
HelloBeen struggling with a Cisco 1120 today, no warranty left, but would like to get it running again. Tried a new disk and flashed it with tftp from rommon, also tried USB. Unit comes up with FXOS, but not able to install FTD with scope --> firmwar...
We have a 3110 with version 7.6 managed by FMC 7.6. The flow is User >> WLC >> Core Switch >> Cisco FTD >> Internet Switch >> ISP Router 1 & ISP Router 2. On FTD we have created sub-interfaces of 10 Gig link and we have two 1 Gig links from ISP. We a...
Hi All , After done install and configure ASAv . If I want to upgrade Esxi Version from 6.0 to Version 7.0 Can I do that , Now ASAv Version 9.16 . I try to check ASAv can support Esxi 7.0 but I'm not sure about process upgrade esxi software . What wo...
We are having issues establishing a port-channel between an FTD 3110 and ASR 920. FTD LACP mode is set to "Active" while the ASR is set to "Passive". But it doesn't work.However, we have seen the FTD 4110 with an LACP mode of "On" and ASR "Passive" w...
Dear TeamI have downloaded the vfmc for esxi 7.4.X and 7.3X but i cannot deploy in VMware after deployment its retturn "operating system not found"any ideaRegards
Hi Team, We are having nearly 250ms latency between our FMC and FTD, Will there be any issue ? And we are planing to Add this FTD to the FMC, what all are the consideration I have to take here? or Any load test I can perform to test the reliability ?
Resolved! FTD over Remote FMC - 2 FMC Setup
Hi All, I'm in bit of a pickle here as I have a task at hand that has 2 FMC's and 2 FTD's present: Below is the scenario; In an existing setup that constitutes of a FMC(VM) and local FTD's deployed in HA, lets call them FMC-A and FTD-1) are in produ...
I am experiencing an issue with the software image on a Cisco Firepower 1010 device. After performing a factory reset, I accidentally erased disk0:, which resulted in the loss of the system image. As a result, the device can no longer boot and is cur...
Hello,We are using a Cisco ASA 5525 firewall and have recently migrated our WAN interface and renamed it. As a result, we need to update all ingress rules by changing the interface from "outside" to "wan".access-list outside_access; 10509 elementsIs ...
Hello,I would like to grant an administrator read-only access limited to Access Rules, NAT Rules, and Objects via ASDM.I have already configured TACACS+ authentication and authorization using Cisco ISE, however I’m struggling to identify the exact sh...
I currently have an FTD that has public DNS configured on the management interface (>show network, >show DNS system have Umbrella IPs). I have internal DNS IPs assigned to inside data interface using the platform policy. I did not check enable DNS...
Resolved! Port Scan Enablement in RAVPN Gateway
Hi Team,I have enabled the Port Scan in the ACP which is configurd for the RAVPN gateway, when I run the scan I am able to see the port 443 is opened but there is no logs in the Events. We are managin the FTD via FMC. I am new to Cisco FTD. I was a P...
