Hello , i have an ASA firewall ( 5525) and i want to configure a scheduled backup , is there any documentation about this please ?best regard
Forum Posts
Resolved! Talos Connectivity Problem
Hi to all ,i am getting many messages as the following:Severity: criticalModule: Talos CommunicationDescription: 3 modules failed:* URLDB- Failed to retrieve beaker inventory* LSP- Failed to retrieve beaker inventoryMy subscription is active (it expi...
Hello everyone,I’m working with a Cisco Secure Firewall 1210CE Threat Defense running software version 7.6.4-69, protecting a small LAN.To improve security, I segmented the network into two VLANs:VLAN1 – 192.168.0.0/24: Oracle Database Server 19c on ...
Resolved! Asymmetric Routing with Firewalls in HA
Recently, an interviewer asks me about Active/Standby HA. His question was what'll happen if the tcp ack get's back from the standby firewall, considering the configuration is stateful which means state tables were shared between both.In my opinion t...
Hello all, I wanted to see if anyone knew if i am able to download and push the newest secure client software on our older ASA. We currently use anyconnect ver 4.10 and would like to get this higher prior to our migration to FMC. I only see Secure Cl...
Resolved! FMC 7.6.5 remote backup failing
Hi,We have 5 FMC servers which have been upgraded recently from 7.4.2 to 7.6.5. I found out that since then the daily backup of the FMC server towards a Linux server (Ubuntu 20.04) is not working anymore. The firewalls are still running on version 7....
I am trying to migrate FPR 2100 FTD to FPR 3105 FTD. Both of them are managed by the same FMC. The FPR3105 has only one configured interface: the management interface. When I use the migration from the FMC, it fails after mapping the interface. Any r...
Hi all,I'm a student doing home-lab practice with an ASA 5500-X / FirePOWER setup. Cisco has since removed these files from the download portal, so I can't verify them against the official checksum anymore.Could someone who downloaded these directly ...
I have a couple Firepower firewalls that run ASA image. Should I change the image to FTD? In that case should I use FMC or managing the FTD via FDM would be enough?As far as I know FMC provides more features that configuring an FTD via FDM, isn't it?...
Hi everybody; My lab consists one FMCv with version 7.4.2.3 and one FTDv in Routed mode with version 7.4.2.3. I have created an Access Control Rule with the following conditions: I have also configured the logging operation as follows: Now when a...
I am troubleshooting an issue where syslog messages from a firewall do not include the configured hostname or any other device identifier.The affected device is a Cisco Secure Firewall 1220CX running FTD 7.6.2-329.The hostname is configured on the de...
In fmc version 10 i see this critical alert Security Intelligence2 System feeds failedresponse processing failed for Cisco_DNS_Intelligence_Feedresponse processing failed for Sourcefire_Intelligence_Feedi logged in the fmc cli and i can connect to u...
I’m a bit confused about Dynamic NAT and PAT on Cisco ASA.When I configure Dynamic NAT/PAT, an inside host initiates a connection to an outside host, and the ASA creates a translation and connection/state entry.My question is: if a new connection/req...
Hi Cisco Community,cc: @dwiprasetyou I want to ask, I have FTD Appliances Registered on FMC, from FMC Gear Icon -> health -> Monitor, we can see Disk Usage Entire Disk and Critical Partition.- Entire Usage usually low (not sure what it's contains)- C...
I am trying to register my FTD with the Smart Account. It is failing. I checked from the CLI; I can ping Cisco from the outside interface but cannot from the management interface. I think the license registration is done through the Management. Is it...
