Hello everyone,We are running an ISA 3000 firewall currently imaged with FTD firmware version 7.4.2.3-4. The firewall is a single stand alone device, managed through FDM. We do not have FMC.Cisco has updated their "Golden Standard" version recently t...
Here's the situation I'm in: My customer has a virtual FMC that manages the SFR modules in three ASA-5516s. That runs version 7.0 as we have found anything newer doesn't work.We are in the process of migrating off of the ASAs and onto three 1140s. I ...
Hi can someone help me with the configuration of ASA 5545Xseries? I have the router to the 0/0 and one pc on 0/1.I want to use dhcp to have internet access.Can you please give me a complete example cause the previous asa i had were using different co...
Hello, can someone please help me configure these 2 ? I connect the router on the 0 int and at the 1 my pc.I want dhcp.Please help me.The commands are different from the 5510 and 5520 i had.
Hi all!I have a question about ASA cluster failover. Failover LAN interface shows the following error:CGD600167DVPN1/sec/act# sh failFailover On Failover unit SecondaryFailover LAN Interface: Failover Ethernet1/11 (Failed - No Switchover)Reconnect ti...
I have Firepower Management Center (FMC) 2600 managing Cisco Firepower 4150 (which will be end of life by August 2025) and my employer has purchased the Firepower 3140 as the replacement. I talked to Cisco sales a few months ago and they said the mi...
Hi to all ,i am getting many messages as the following:Severity: criticalModule: Talos CommunicationDescription: 3 modules failed:* URLDB- Failed to retrieve beaker inventory* LSP- Failed to retrieve beaker inventoryMy subscription is active (it expi...
Hi.We are currently facing issues when trying to automate the "admin" username via Ansible remote command execution.We have a Cisco Firepower 2130 Threat Defense Version 7.4.2.2 (Build 28) which is manged via our FMC version 7.4.2.3.Anytime we try to...
Hi! I'm migrating ASA to FTD 3110. I got an issue during validation where "OSPF configuration already exists on the cisco FMC. Please disable OSPF on the FMC before proceeding with the migration." I am migrating a transparent mode FW and there is no ...
Greetings,We have a Cisco 2130 Firepower FTD that we recently attempted to upgrade the software version 7.4.2.2 to 7.4.2.3-4.Via the Cisco 2600 FMC, we ran the update via Setup - Product Upgrade - and selected the device. The package uploaded, the c...
I am trying to lab FMC deployment with the 90 evaluation. I added two virtual Firepower's to FMC but the starter policy that you must create when adding them, fails to deploy with the message "The deployment failed because the deployment packages did...
HiQuick question, Is it possible to Configure a RB VPN on an FTD using a Loopback Interface.??I ask because I have been requested to set up one but the thing is the peer IP I have to use my side is not one of the FTD Interface IP Addresses, Also is t...
Our current ACAS scans are showing plugin 157288, TLS Version 1.1 Deprecated Protocol findings on Firepower 4120 and Firepower 4125 with FTD devices.The Firepower 4120 is running version 7.2.9,The Firepower 4125 is running version 7.4.2.2I am asking ...
Our current ACAS scans are showing plugin 51192, SSL Certificate Cannot Be Trusted on Firepower 4125 with FTD devices.The Firepower 4125 is running version 7.4.2.2I am asking if there is a correct method to resolve plugin 51192. It my understand the...
Our current ACAS scans are showing plugin 57582, SSL Self-Signed Certificate on Firepower 4125 with FTD devices.The Firepower 4125 is running version 7.4.2.2I am asking if there is a correct method to resolve plugin 57582. It my understand the FXOS,...
