02-26-2008 12:33 PM - edited 03-13-2019 05:00 PM
Does anyone know how to configure a meet-me conference on a UC500 via the CLI? The configuration notes for CME 4.2 don't seem to apply, since the UC500 does not have the required dspfarm pool. I would appreciate any help! Thanks, Dennis.
02-26-2008 01:49 PM
Meet-me must use dspfarm, why do you say that is not in the uc500? Don't you see two voice-cards in config ?
02-26-2008 02:48 PM
Thank you for your reply.
I'm new to the UC500 and CME platform in a lot of ways (coming from full server-based CallManager), so I might be missing something here. This is what I see from the command line:
Before Config:
#sh dsp
DSPFARM Configuration Information:
Admin State: DOWN, Oper Status: DOWN - Cause code: ADMIN_STATE_DOWN
Transcoding Sessions: 0(Avail: 0), Conferencing Sessions: 0 (Avail: 0)
Trans sessions for mixed-mode conf: 0 (Avail: 0), RTP Timeout: 600
Connection check interval 600 Codec G729 VAD: ENABLED
Config (start):
dsp services dspfarm
After Config:
#sh dspfarm ?
all Display all DSPFARM global info
dsp Display DSPFARM DSPs information
profile Display DSPFARM profiles
#sh dspfarm all
Total number of DSPFARM DSP channel(s) 0
#sh dspfarm dsp active
Total number of DSPFARM DSP channel(s) 0
Am I on the right track?
Thanks,
Dennis.
02-27-2008 11:09 AM
Here's the config I use in a customer install, to support 2 x 8 parties G.711 conferencing only. There is only one set of ephone-dn for conference configured. The remember to cofngire the meet-me softkey in ephone-template.
voice-card 0
dspfarm
dsp services dspfarm
!
voice-card 1
no dspfarm
! recommend use of loopback
sccp local Loopback0
sccp ccm 10.6.4.200 identifier 6200 version 4.0
sccp
!
sccp ccm group 100
bind interface GigabitEthernet0/0.4
associate ccm 6200 priority 1
associate profile 10 register confdsp1
!
dspfarm profile 10 conference
codec g711ulaw
maximum sessions 2
associate application SCCP
telephony-service
sdspfarm units 1
sdspfarm tag 1 confdsp1
conference hardware
!
ephone-dn 192 dual-line
number 693
conference meetme
no huntstop
!
ephone-dn 193 dual-line
number 693
conference meetme
preference 1
no huntstop
!
!
ephone-dn 194 dual-line
number 693
conference meetme
preference 2
no huntstop
!
ephone-dn 195 dual-line
number 693
conference meetme
preference 3
Hope this helps, please rate post if it does!
02-27-2008 12:21 PM
Thank you very much for this. I will give it a try and let you know how I make out.
Dennis.
08-19-2008 10:21 AM
Picking this up again after some time and for a different customer location... this config really did help. Thank you.
09-09-2008 09:37 AM
Paolo,
This configuration also helped me, with a problem I had with the dspfarm not registering with SCCP on a UC500, except that I am using multi-party ad-hoc instead of meet me conference.
Everything now looks fine but when the folks press the Confrn softkey they get a message "no line available". The only thing I haven't tried is resetting the entire system.
I've attached the whole configuration in case there is something I've missed, but I think I have covered everything I could find in the documentation. If you could look through it when you have the time I would appreciate it.
Thanks,
Mike
01-05-2011 06:41 AM
Thank you very much for this configuration example. i successfully configured it today..
This manual helped me great too:
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide