Other Network Architecture Subjects

I'm trying to create two Vlan's on a Cat 2950 using a 1604R for routing. I create the Ethernet subinterfaces on the router but don't know how to config the vlan trunking using dot1q. Any help would be appreciated.

Does CW2000 with RME 3.1 support the import of PIXs in the inventory database? I cannot seem to get it to import, and would like to know if it is even possible.

There is a lot of confusion about running dlsw+ between two routers.For example, If a there is a peer relationship between r1 and r2.r1 config,dlsw local-peer peer-id 1.1.1.1dlsw remote-peer 0 tcp 2.2.2.2r2 config,dlsw local-peer peer-id 2.2.2.2dlsw ...

Hi,I'm looking for a SNMP OID that provide a MAC-address table of the 3548 model switches.. I have fond the OID for the 3550 in the Stack MIB but it sams that the 3548 do not support the Stack MIB..I Hope that one of you can help me

Ok, I have what should be a fairly simple situation here, but I am unsure as to how *exactly* to do it. I have a CAT 4006, sup II engine that is presently acting only as a layer 2 switch. There is nothing fancy on it at all..... In fact, about the ...

Also on another 2611 router i make changes to the start up config, and they are saved. but when i look at the running config, there is this one line in my access list that won't get removed. its not in my start up config only in my running config. i ...

I am connecting a Real secure IDS in a catalyst 4006 with WS-C4006 Software, Version NmpSW: 6.3(1).What I need is to enable span or port mirroring in my catalyst but with the ability of wrtiting on the port, because one of the funcionalities of this...

I have a 2610 with 2 ethernet interfaces and IOS 12.2(16). The ip addresses for those interfaces are 172.16.0.90/16 and 172.25.0.1/16.I can ping all hosts on 172.16.0.0 subnet from the router using the 172.25.0.1 interface as source. But when I try t...

Hello All,I'm getting my feet wet with ISDN.I'm looking to setup 26 remote offices housing 802 ISDN routers. The reason for the connectivity is to manage each site and give them access to the internet via our Frame Link at the central office.I'm look...

My client is using Cisco router 678. When I enabled ports 5632 and 5631 for pcanywhere by using set nat entry add 10.0.0.50 5631 223.224.83.2 5631 tcp and set nat entry add 10.0.0.50 5632 223.224.83.2 5632 udp, it worked fine. Now, they want me to ad...

I am running the standard syslog facility for Solaris, collecting syslog info from Cisco routers.Recently, we started seeing a bracketed, 6 octet string in place of some of some of the host names. The first 4 octets are an IP address from the router...

Hi there,My company has two sites, each with two core switches. Our main site has a 6509 and a 6513. Our second site has two 5509s. The 5509's are due to be replaced. The plan (very rough at this stage) is to take the 6509 and 6513 from the main ...

Does it possible to receive normal incoming traffic in the SPAN destination port on C4507?I like to mirror a port but I need that the destination port has the capabilty to receive normal incoming trafficThe "old" CATOS for Cat 400x and 650x permit t...

Is there anyway to utilize ciscoview to monitor interface statistics on a vwic? We have a number of routers with vwic's that have been configured so that all 24 ds0's are mapped to serial0/0:0. When selecting the monitor option, Ciscoview provides...

I am trying to manage my Cisco IP Phone (Cisco 7690s) environment using CWLMS 2.1 Topology Services. The icon it gives the phone is a switch and the description is that it is a 3550-48. Can anyone shed any light on this?Thanks in anticipationNick :-)