Would like to check if this IOS supports IPSEC software

[ahpark78]

Hi Gurus,

Would like to check the IOS Below if can support IPSEC implementation.

I have checked on the config t --command,but didn;t find any IPSEC.

WOUld like to confirm if tis IOS supports,if not, can i do an upgrade to diff IOS?

---------------------------------------

Cisco IOS Software, C1700 Software (C1700-K9O3SY7-M), Version 12.3(8)T3, RELEASE SOFTWARE (fc1)

---------------------------------------

thanks !

ken

[Richard Burts]

Ken

In general IOS images identified with K9 in the image identification do support IPSec. I do not recognize the specific identication line that you provide. If you would also post the part of show version that includes the file name in flash it would give us a better identification of the image and we might be better able to answer your question.

But baiscally I believe that yes your imaage does support IPSec. What commands were you looking for to verify support of IPSec?

HTH

Rick

[Edison Ortiz · Accepted solution]

Ken,

"k9o3sy" indicates the product is part of the

IP/FW/IDS PLUS IPSEC 3DES - feature set.

what command are you looking for ?

Please read this URL

http://www.cisco.com/en/US/customer/tech/tk583/tk372/tech_configuration_examples_list.html

on how to configure IPSEC with Cisco routers.

Please rate helpful posts.

Thanks

[ahpark78]

Thanks Rick,Edison!

Just to confirm with the sh-ver..Will rate

you guys post once confirmed with the sh ver.:)

thanks again!

----------------------------------------

Router#sh ver

Cisco IOS Software, C1700 Software (C1700-Y-M), Version 12.3(4)T7, RELEASE SOFTW

ARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2004 by Cisco Systems, Inc.

Compiled Mon 19-Jul-04 11:45 by eaarmas

ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)

Router uptime is 2 hours, 51 minutes

System returned to ROM by power-on

System image file is "flash:c1700-y-mz.123-4.T7.bin"

Cisco 1760 (MPC860P) processor (revision 0x500) with 54868K/10668K bytes of memo

ry.

Processor board ID FOC08300U1F (2150418580), with hardware revision 0000

MPC860P processor: part number 5, mask 2

1 FastEthernet interface

1 Serial(sync/async) interface

1 ISDN Basic Rate interface

32K bytes of NVRAM.

32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

[ahpark78]

Btw, Edison,

The link you given me not able to access.

Need to have a CCO account. Can provide me the actual link with a public access then?

thanks!

ken

[rajinikanth]

Hi,

Check this link

http://www.cisco.com/en/US/products/hw/routers/ps221/prod_bulletin09186a00800ab6bd.html#wp39434

Hope it helps you

Raj

[desai.jaideep]

Hi

Though your IOS support the IPSec feature, following is the link which can assist you further:

http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp

Pls rate helpful posts.

Regards

JD

[ahpark78]

But guys,

the funny thing is there is no crypto command under the config term mode.

Am i missing something??

As i believe the ipsec should have this command to configure ipsec rite?

Or any links that can point me to IPSEC configuration will be much appreciated! :D

thks!

ken

[ahpark78]

hi,

i have checked on the tools image, there is no IPSEC support,Am i going wrong somewhere..?

thanks!

rgds,

kenny

[rajinikanth · Accepted solution]

Hi,

Check this to help you in configuring Ipsec

http://www.cisco.com/en/US/products/hw/routers/ps221/products_configuration_guide_chapter09186a008007cd15.html

Raj

[jolmo · Accepted solution]

Hi Kenny

You have posted:

"Cisco IOS Software, C1700 Software (C1700-Y-M), Version 12.3(4)T7, RELEASE SOFTWARE (fc2)

....

System image file is "flash:c1700-y-mz.123-4.T7.bin"

This is an IP IOS Feature Set. It does NOT support IPSec

Hope this helps

[ahpark78]

You are right, Jolmo!

So, the next question will be, can I upgrade the IOS to diff IP Feature Set.

Any cost involved here to get the IOS below with the feature set? I have check that

the IP/ADSL/FW/IDS Plus/IPSEC 3DES can be used for IPSEC>

Can I download the IOS and use it?

thks!

ken

[desai.jaideep]

Hi

I dont know why you are confusing things over......Pls be amandament that which router you want to configure.....the first one or the second one.....

Earlier Post:

Cisco IOS Software, C1700 Software (C1700-K9O3SY7-M), Version 12.3(8)T3, RELEASE SOFTWARE (fc1)

Current Post:

Cisco IOS Software, C1700 Software (C1700-Y-M), Version 12.3(4)T7, RELEASE SOFTW

ARE (fc2)

Pls rate helpful posts.

Regadrs

JD

[ahpark78]

Sorry Desai for the confusion,

it will be this version..

Cisco IOS Software, C1700 Software (C1700-Y-M), Version 12.3(4)T7, RELEASE SOFTW

ARE (fc2)

Now i am almost there..just need to know if

the IOS feature set can be upgraded without

any costing...

[jolmo]

It depends on your service level. Do you have any service contract for this router?

If not, you will have to order.