I have an 831 with an external modem attached using the Aux port of the 831. I was just wondering if anyone has a basic config for getting the modem to dialout. I am using it as the main interface and not the backup. Thanks.
I have an 831 with an external modem attached using the Aux port of the 831. I was just wondering if anyone has a basic config for getting the modem to dialout. I am using it as the main interface and not the backup. Thanks.
PIX501->C1841->Network Cloud->C1841->PIX501Both cisco1841 run GRE. So is the link secure if GRE is running on both C1841 instead of running on PIX501? Please advise or correct me thank you very much any help is deeply appreciated
I'm a noob so keep it simple for me. I'm not good at the commands.I want to lock down my PIX 501 (v.6.2) by doing the following:Disable all incoming traffic except if initiated by someone on the inside and https access to one web serverBlock all outg...
I have a new asa5520 in which I am using NAT; I have a DMZ and two internal interfaces. I need to setup RDP access (temp) to all three interfaces. I am able to RDP(port3389) into a server on the DMZ but I cannot access either of the two internal inte...
I have an unusual scenario where I have a VoIP device that won't work behind NAT.Is there a way to assign public IP's to certain hosts in the DMZ, yet still NAT to a private address for another host on the DMZ? All static mappings would be fine...
I have 3com super stack 3226 which is a multi layer switch. I have three vlans configured on it. VlanA with an address of 192.168.1.0, VlanB with an address of 192.168.2.0 and VlanC with an address of 192.168.3.0. I can get the vlans to talk to each ...
Below is a snippit of the pertinant part of a config on one of my routers. The "show logging" indicates that items are being logged (via trap), but nothing's being sent to the logging host, "192.168.145.16". What am I missing? Is syslog on Cisco ...
I can route traffic over port 3389 to DMZ but the same rule doenst allow 3389 to the internal networks. External on port 0, dmz on 1, internal networks on 2 and 3. I allow connections to internal port 3389 from source "outside" IP to my internal "Des...
Does anyone know if the PIX can act as ACTIVE/ACTIVE over the wan (the wan connection is 90Mbps).I saw no info in the docs that says that it can not.
Good Day All,Has anyone had to boot their fwsm into the maintenance partition while the catalyst switch was in a production network.I have found the command hw-module module x reset cf:1; but am a little hesitant to use it.... Currently... we have i...
Hello,On my pix I use static route with DNS doctoring to translate request from a public IP on the outside interface to a private IP of one of my machine on the inside interface.Ex :static (inside,outside) 213.251.23.146 192.168.1.56 dns netmask 255....
Can the PIX be configured with an inside address that translates to a destination address? I would like clients to connect to a server that is on another network but, do it via a local IP.
Hi I have FWSM configured in a 6500 chassis. The MSFC is logically installed before the FWSM which means the firewall is the one connected to the internet. I have only one VLAN shared between the MSFC and the FWSM. The problem is that the FWSM can re...
(This rule locks down the application by placing restrictions on file operations. If an application becomes compromised (buffer-overrun attack), this rule limits what types of files can be accessed by the application.)My question is ...this rule DENI...
I'm going to be setting up a site-to-site between 2 remote offices and my main site.main site will have a 2821 and the remotes will be 837 and 831.main site - internal ip is 172.18.1.1, external is 216.3.1.1remote1 - internal = 172.31.2.33/27; extern...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-04-2024 12:11 AM | ||
08-14-2024 02:32 AM | ||
08-13-2024 10:56 PM | ||
08-07-2024 05:42 AM | ||
07-05-2024 02:02 AM |