Cisco’s security team has released an advisory for: RV340 Series Small Business routers (PSIRT Notice) Fix for bug CSCwc53007- RV34x GUI not accessible – The recommended fix is to upgrade to firmware version 1.0.03.29RV082, RV042, RV016 (PSIRT Noti...
Forum Posts
Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Virtual Assistant - Discover support content and options for your gearSupport page index - Contains a...
I have some difficulties whit my RV130 Router. The short story is that I can’t connect to my NAS and windows server through PPTP VPN (windows 10 client). When I try to connect, I get the following error in windows “A connection to the remote computer...
Hello I wanted to know how to put a router RV132W in server or client mode to create an ipsec VPN tunnel, but I did not find the option to put it in client or server. Thank you for your help.Verry Urgent Please Help.
A blast from the past. We found an old Cisco SB101 router in a closet that's running some archaic production servers. It's connected to a PIX 501 and a 3560. Needless to say, now that I'm aware of this ancient equipment, it needs to go. I was able to...
Hello team, I have a 2951 router which reloads itself every 4 hours. Very strange but would be appreciated if you could give me some tips resolving this issue. Here is some configuration info: sh versionCisco IOS Software, C2951 Software (C2951-UNIV...
I am using RV320 for my wireless users. I am confused about how to perform NAT for them so that they can access internet. I checked PAT option on GUI but did not understand much. Also checked Admin guide.
Hi,Is there a way to broadcast an WOL command from RV345 into the network behind it? If not, this is a feature request which should be easy to implement. Regards,
Hey guys, Last week I upgraded the RV340 firmware to 1.0.0.216 and after that I got frequent AWS VPN dropout during the day. It happened almost 5 times a day. Luckily I got a config backup so I can reset and reinstall the older firmware. After rest...
Hi there, I have been unable to find out IOS XE configuration file converter toll. its name may be cedge tool. This tool use for migrating IOS XE into SD-WAN. if any one has this tool information please send me link. Thanks in Advance. Ashish
Hi Team, After upgrading the firmware to the latest firmware version 1.4.2.20 I am able to access the GUI page via LAN but not via WAN port. Since this device is another location we need to access the GUI via WAN port. I have enabled the remote man...
Hi, We have this network configuration in RV345: WAN1: ip: 192.168.1.11 /24 VLAN1 ip: 192.168.3.11 /24 Hardware DMZ Enabled (port 16 to DMZ) ip: 192.168.2.11 mask: 255.255.255.0 DMZ Host Enabled ip: 192.168.2.11 I'm trying to allow traf...
Does RV345 have block diagram like mikrotik?https://mikrotik.com/product/rb4011igs_5hacq2hnd_in#fndtn-downloads
Hi Group,It seems that a RV345 behaves differently than a RV325 with a static route.Originally a Fortigate 50, then for a short period a Netgear one and later a Cisco RV 325 worked with basically the same Setting... RV345 doesnt...Setup:RV325 on WAN ...
Hello, I've a problem with port forward on my rv042g. i've a raspberry pi running openvpn server (pivpn). I need to open up udp port 1194 for my pi. i added on access rule under firewall, allow udp port 1194, source interface - any, source ip -any...
I was checking my DYN DNS account and looking at the update log and it appears the RV345's are updating DYN DNS every 3 hours even though there's been no change. So I logged in two different RV345's and under edit Dynamic DNS there is an unchecked b...
I am using an RV325 router.I bought the RV345 to replace the RV325.For the RV325 put the Wan in bridge mode it's very simple and it works well.Just select bridge mode and do Apply and that's it.I do the same thing on the RV345 but here the router dis...