Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Interchassis High Availability vs HSRP (ISR4k)

Hi, I read the Interchassis Redundancy documentation and it mentions it uses HSRP. Is it in the background?  or  HSRP should be configured?. What will be the best practice?  Not sure combining  Also is there an explicit comparison son why to use Int...

fgotopo by • Cisco Employee
  • 1325 Views
  • 1 replies
  • 0 Helpful votes

Route selection

Hi Friends, Hope you all re doing good :) I have one query, If i have configured one router to reach the destination as below: Source: 192.168.1.1 Destination : 10.0.0.5 1. I configured Static Routing 10.0.0.0/24 2. I configured for OSPF Here i...

Resolved! Advertise /24 and /32 (same subnet) BGP?

Hi all, First time poster.  Can't find much information out there on this.  I tested advertising (10.80.80.0/24) and (10.80.80.1/32) in GNS3 via BGP.  As expected BGP only advertises the more specific prefix.  I was told by my Sr. that you could adv...

Cisco C887VA-K9 Connectivity Block

Hi everyone, I have problems with the Cisco887va-k9 router. I use this for connettivity adsl2+ or vdsl. After about 10 days this router goes to block, I can not ping it but the adsl or vdsl session is always up! Of course I have to reboot the router ...

simomau91 by • Level 1
  • 837 Views
  • 4 replies
  • 0 Helpful votes

Resolved! 10GLANPHY protocol configuration on Cisco Nexus Switch ?

Hi I would like to check if 10GLANPhy can be configured on the Cisco Nexus switch to form a fiber to fiber connectivity between 2 data centres at different site. The 10GLANPHY protocol statement provided by the local ISP, asking if our switch can han...

Ken Le by • Level 1
  • 708 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Any show command to show the EIGRP feasible succcessor

Hi gents, How do I know if a path in my "show ip eigrp topology" table is FS or not? EIGRP-IPv4 Topology Entry for AS(100)/ID(10.128.121.1) for 10.128.0.0/14 State is Passive, Query origin flag is 1, 1 Successor(s), FD is 24096000 Descriptor Blocks: ...

Capture or Monitor Interface traffic on MWAM

Hello, I have a Cisco MWAM using Version 12.3(14)YX14. I am not able to run capture at interface level on this device. What would be the command to capture ? Ideally I would be expecting monitor capture MYCAP interface (xyz) and a few other commands ...

Jay Joshi by • Level 1
  • 712 Views
  • 0 replies
  • 0 Helpful votes

Problem with csr1000v booting and startup console using gns3 in windows 10 environment and VirtualBOX oracle.

Dear All,I am facing  problem to open consol of csr1000v from gns3 , i am using virtualbox from oracle.each time i get the error like ...Prentinue.Press any key to continue.    GNU GRUB  version 0.97  (639K lower / 2071488K upper memory) +-----------...

Resolved! show license summary, period left

hello everyone, i have 2 4500 Catalyst with VSS. when i see the "show license summary" i see the output below Switch_Name#show license summaryIndex 0   Feature: entservices          Period left: 8 weeks 4 days          License Type: Evaluation      ...

Resolved! Loopback interface influence in OSPF.

Hi , can anyone help me to understand what happens in OSPF with the Router has 2 loop back interface configured and one loop back is configured with public IP for DMVPN purpose. My question is whether the Loopback interface with Public IP also advert...

Load more