Hello,
We have a HQ and multiple agencies so we choose DMVPN but the issue is that every buildings has a 3 ISP so basiclly
we create 3 dmvpn tunnels and we run 3 ospf proccess the issue is now even when we choose our 1 ISP to be primary some ro...
Hi I have a single router that I would like to use for PPPoE. I have two PPPoE connections and my ISP gave me two different username and passwords. I would be grateful if somebody could help me with the configs. I plan to use two separate vlans on a ...
Dear communityI've a BGP question. I've a router peering with a customer of mine, plain EBGP no MPLS, see following chain as example:myrouterA --ebgp-- myrouterB --ebgp-- myrouterC --ebgp-- mycustomerA --ebgp-- mycustomer_BGP_worldwide_networkAmong m...
Hello,
I has a 1841 router connected in media converter rj45-optical fiber; the interfaces fastethernet have any errors :
FastEthernet0/0 is up, line protocol is up Hardware is Gt96k FE, address is 9caf.ca71.9fb4 (bia 9caf.ca71.9fb4) Description: LAN...
Hi All,, I really need help now guys. I have 8-2960x access switches that is connected to 2-3750x core switches. The uplinks of the 2960x switches will just shutdown unexpectedly even if i just followed the same and old switch configuration. Here is ...
Dear Team I have configured DHCP in Cisco 1841 router , But the DHCP is working fine .Kindly help me to configure Static binding of IP address in DHCP .he Today 30-07-2013 I have tested to DHCP using IP mapping with Mac address as per discussion . B...
Hi,
I have the following situation and looking for an answer, I have 3 routers connected as following
R1 AS 64600 <---> R2 AS 2856 VRF1(MPLS) <------> R3 AS 64620
the 3 routers are connected via BGP mpls, R1 is redistributing default route into BG...
Hi there just bought a cisco 881-w -pretty new to cisco hardware ^^
As i have read i need to config it over telnet ?
But can¨t get any conection to it :/
What i have tried 1: connecting the FE 4 to my fiber modem and FE 0 to my pc --When it boots i ...
I have 2 nexus 5000 switches configured with a trunk linking the two how can i do the follwoingBOX 2vrf context management ip route 0.0.0.0/0 192.162.88.9BOX 2vrf context management ip route 0.0.0.0/0 192.168.88.101. ping between the two boxes, i s...
I have 2 ISP links, 69.74.x.x and a second new one that I just added 108.162.x.x to our Cisco 2900 to increase our overall speed, which is working.
Can the outside NAT connections that are on the 69.74.x.x be affected by adding the new link? I hav...
Does anyone knows if there is an equivalent command to bandwidth qos-reference for subinterfaces on IOS-XE Version 15.5(2)S1c? I can use it on tunnel interfaces but not on subinterfaces.
IOS-XE Version 15.5(2)S1c
(config-subif)#bandwidth ? <1-10000...
Hello guys,
Below my actual conf for cisco c837... the problem is that i cannot access skype if i plug my laptop in any port from f1-4 but web browsing is ok except for some websites such as malwarebytes and viber (webpage cannot be displayed).
wh...
I have a question regarding the startup process of EIGRP. I have noticed that a unicast update is sent in a broadcast segment containing topology information. Why is this?
Below is a screenshot of the EIGRP startup process and of two Update messages;...
Hi, I have deployed Cisco WLC 2504 with 1702 WAPs. WAP users get their ip addresses for WLC dhcp pool. on the other side for WAN we are connected with an ISP through Microtik Router. Recently i have purchase Cisco Router 2911 and configure it for L...
Hi All,
I'm doing a new install for a remote customer. They wish to load balance across 3x new VDSL lines that are being installed. the line provider will supply their own routers on the end of each lines, so I don't have the issue of DSL to Etherne...
