Hello, I'm trying to configure vlans for the installed HWIC-4ESW on a 2821 router running the IOS image c2800nm-advsecurityk9-mz.124-3i.bin. I've entered the following:R(config)# vlan ?accounting VLAN accounting configuration As you can see above, I...
Hello,I've intalled two HWIC-1FE on a C2821 router. All 3 LED lights are on each card. However, the IOS does not see them...Could you please help?Thanks,Frank
I have a 7609 that has one of the processor cards stuck in a Standby cold state, this became an issue when we removed and re-added syslogging the other day. Both SUP Modules are running the same version of code which is 12.2(33)SRB5, looking for some...
Hi folks,I have two routers connected via two MGX as the diagram given below.PC1 <--> R1 <--> MGX1 <--> MGX2 <-->R2 <--> PC2The concern is while transfering the data from PC1 to PC2 (say FTP, etc), I find a huge delay: say about a minute to transfer ...
I want to know if its possible to do this.I have the following network setupASA 5520 ---> Cisco 2801 ----> T1 I want to add an addtional internet subnet. These will have a different IP range. I dont need to load balance i just...
Hi, I have two ASA in US (inside network 10.0.0.0/24) and India. I am controlling US. I have created IPSEC peer-2-peer IPSEC tunnel.On US side, I have allowed 10.0.0.0/24 as source of interesting traffic in Cryptomap ACL. On India side, tech has open...
Hello1)what is the benifits of using switch for the inside and switch for the outside and switch for the DMZ?2)is it possible to put all the connection for inside,outside,DMZ on the 4507R instead of dedicate switch for each segment?please clarifythan...
GreetingsI am useing a 2811 Cisco Router at my company to access the Internet trough my serial interface 0.At this moment the pages on the internet go up and down. Meaning:When I insert a URL its gives me the error message that the page could not be ...
I have to install the Cisco 2800 with IOS ITP 12.4(11) Please guide me what I have to configSWure for the ITP,This is the first ITP installation I am going to do.Then I was trying to download the folling PDF,but it is asking the valid username and pa...
Good Morning,My question is about "L3-L2 Dynamic Map" Interval Refresh?I was doing labs with frame relay and I was used the debug command "debug frame-relay event", the output was:Mcbo#Mcbo#sh logSyslog logging: enabled (12 messages dropped, 8 messag...
EIGRP metric calculation?I have a 6513 with EIGRP routing protocol.When I try to calculate the EIGRP metric of a interface loopback 0, using the bandwidth value and delay value that show interface loopback 0 command.es-plcdatacenter2#sh int looes-plc...
Hi,A co-worker of mine used a command to determine how many bytes per MAC address connected to a switch transferred. I think it might have been an accounting command but I can't seem to get it to work.All I remember is it showed this data based on th...
I have a 4506 catalyst switch with no ip addressthe cdp neighbor info is as follows (all neighbors in the 119 subnet /24 mask)CAT11#sh cdp neigh detDevice ID: router1Entry address(es): IP address: 192.168.119.241Platform: Cisco 3825, Capabilities: ...
Hello.I have this log (see attach) when I reload the 8850 and the prompt is :pxm45bkup>I tried to Initializing the Switch but I didn't find any file sys in the disk:pxm45bkup>cd "C:FW"value = 0 = 0x0pxm45bkup>lsataBlkRW : installed or diskok E...
I am trying to setupa site-to-site VPN. Site A router is 79.129.63.208, site B router is 213.249.2.6. The server 10.0.0.50 to site A should exchange data with network 10.10.33.0/24 to site B.The tunnel is not established. I get the state "MM_NO_STATE...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-14-2025 01:24 AM | ||
| 05-12-2025 03:28 PM | ||
| 05-09-2025 02:25 PM | ||
| 05-05-2025 11:47 PM | ||
| 04-22-2025 12:20 PM |
| User | Count |
|---|---|
| 9 | |
| 7 | |
| 4 | |
| 4 | |
| 3 |
